MR VACUTAP VMS страница 46 Скачать руководство пользователя | Manualshive

Страница: 46 / 80

background image

7 Maintenance

Maschinenfabrik Reinhausen GmbH 2020

46

5993419/02 EN

VACUTAP

®

VMS

®

7 Maintenance

DANGER

Electric shock!

An energized transformer could cause death or serious injuries.

► Switch off transformer on high and low-voltage side.

► Lock transformer to prevent unintentional restart.

► Ensure that everything is de-energized.

► Visibly connect all transformer terminals to ground (grounding leads,

grounding disconnectors) and short circuit them.

► Cover or cordon off adjacent energized parts.

DANGER

Electric shock!

Working on the on-load tap-changer when on-load tap-changer components
are energized can lead to death or serious injuries.

► De-energize all auxiliary circuits, such as the tap-change supervisory de-

vice, pressure relief device, pressure monitoring device.

► Make sure that everything is de-energized.

WARNING

Danger of explosion!

Explosive gases in the oil compartment of the on-load tap-changer, trans-
former, pipe system, oil conservator and at the dehydrating breather open-
ing can deflagrate or explode and result in severe injury or death.

► Ensure that there are no ignition sources such as naked flames, hot sur-

faces or sparks (e.g. caused by the build-up of static charge) in the trans-
former's immediate surroundings and that none occur.

► Do not operate any electrical devices (e.g. risk of sparks from impact

wrench).

► Only use conductive and grounded hoses, pipes, and pump equipment

that are approved for flammable liquids.

NOTICE

Damage to motor-drive unit!

Damage to the motor-drive unit due to condensate in protective housing of
motor-drive unit.

► Always keep protective housing of the motor-drive unit tightly closed.

► In the event of operation interruptions of more than 2 weeks, connect and

operate the anti-condensation heater in the motor-drive unit. If this is not
possible, e.g. during transportation, place a sufficient amount of desiccant
in the protective housing.

«
...
44
45
46
47
48
...
»

Содержание VACUTAP VMS

















































































Отзывы:

Нет отзывов

Похожие инструкции для VACUTAP VMS

Бренд: ABB Страницы: 14

Бренд: Febco Страницы: 12

Бренд: Yetter Страницы: 16

Бренд: e+p Elektrik Handels Страницы: 2

Бренд: idi Страницы: 20

Бренд: G&G Страницы: 2

Бренд: H&S Страницы: 46

Бренд: Pablo Страницы: 7

Бренд: M-system Страницы: 2

Бренд: Rico Страницы: 34

Бренд: iHealth Страницы: 8

Бренд: Kärcher Страницы: 88

Бренд: H&S Страницы: 42

Бренд: Rainin Instrument Страницы: 16

Бренд: VDO Страницы: 15

Бренд: VDO Страницы: 20

Бренд: A&D Страницы: 29

Бренд: Yamaha Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды