MR VACUTAP VMS страница 53 Скачать руководство пользователя

Страница: 53 / 80

7 Maintenance

Maschinenfabrik Reinhausen GmbH 2020

5993419/02 EN

VACUTAP

VMS

4. Once the gas has been discharged and insulating fluid is flowing out of

the air-vent valve, close the air-vent valve.

5. Close the stop-cock between the oil conservator and on-load tap-changer.

6. Open air-vent valve E1 again and extract approximately 5–10 liters of in-

sulating fluid via the pipe connection S until the area under the on-load
tap-changer head cover is free of insulating fluid.

7. Remove the screws and washers from the on-load tap-changer head

cover.

Figure 26: On-load tap-changer head cover

8. Remove on-load tap-changer head cover.

Figure 27: On-load tap-changer head cover

9. Extract insulating fluid via pipe connection S.

10. Open the stop-cock between oil conservator and on-load tap-changer.

The insulating fluid flows out of the oil conservator into the oil com-
partment.

11. Extract insulating fluid via pipe connection S.

Содержание VACUTAP VMS

















































































Результаты поиска

Содержание VACUTAP VMS

Отзывы:

Похожие инструкции для VACUTAP VMS

Бренды по названию

Популярные бренды

MR VACUTAP VMS, Руководство по эксплуатации

Результаты поиска

Содержание VACUTAP VMS

Отзывы:

Похожие инструкции для VACUTAP VMS

Бренды по названию

Популярные бренды