manualshive.com logo in svg

MPC 1250, Руководство оператора, Страница: 41 / 44

Поделиться
Скачать
MPC 1250 Скачать руководство пользователя страница 41

Section VIII 

Trouble-Shooting Guide

006-0007207 MPC-1250DC Guide 

Rev F 

41 of 44 

03/03/2022  

www.synqor.com

LED

Indication

Possible Problem(s)

F0:

MPC Cooling 

System LED

LED is BLINKING 

GREEN

• Indicates that the fans are running at 67% of their rated speed. There 

is no problem.

LED is AMBER

• Indicates that the fans are running at 100% of their rated speed. 

There is no problem, but the unit is operating at a high ambient 

temperature and a high load combination.

LED is RED

• Fans are running at 110% of rated speed to keep the unit cool. The 

maximum recommended temperature may be exceeded, but the 

fans are keeping things cool enough to avoid triggering the over‑

temperature shut‑down circuitry.

C0:

Fan Service 

Required LED

LED is AMBER

• One or both fans have recently had degraded performance but  

seem to be ok now. The MPC is running a diagnostic test.

LED is RED

• One or both fans presently have degraded performance, even  

if they are running, and service is recommended at the earliest 

convenient time.

• Ensure that the fan blades are not obstructed from turning

Audible 

Alarm:

(pattern 

repeats every 

5 seconds)

Two tones

• The total MPC load power is above 1250 W.

• Loads should be reduced if this condition persists.

Three tones

• The DC OUTPUT has experienced either a short circuit or a load 

having a start‑up surge current characteristic that the MPC could  

not start. The DC OUTPUT is in hiccup mode. 

• To reset the DC OUTPUT, turn the unit OFF.  Clear the short circuit 

fault on the end‑use equipment.  Turn the unit back ON.

Содержание 1250













































Отзывы:

Нет отзывов