MPC 1250 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 44

MPC 1250 Скачать руководство пользователя страница 30

Section IV

Constant Current Model

006-0007207 MPC-1250DC Guide

Rev F

30 of 44

03/03/2022

www.synqor.com

Entering and Exiting Charge Mode

The MPC‑1250 for CCCV charging will automatically enter and exit charge mode without user

intervention.

If the MPC is in current limit for at least 30 seconds, it will assume it is recharging a battery, and

enter the CCCV charging cycle. The MPC will recover from current limit when the output voltage

reaches Vtop.

If the MPC is in current limit for less than 30 seconds, it will assume there was a fault or

overload that isn’t a battery. The MPC will recover from current limit when the output voltage

reaches Vset.

The MPC exits CCCV charge mode when the voltage has recovered to Vtop and Ttop has expired

(Stage II has completed). To end Stage II early, the user can set Ttop to a lower value.

Over Power protection will not cause the MPC to enter CCCV charge mode.

Visual indicators - External Battery Charge Level

LEDs E0 – E3 are unique to the Constant Current MPC‑1250 model. These LEDs provide a rough

estimate of the charge level of the external battery. See section VIII for details on all other from

panel LEDs.

POWER OUT

POWER IN

LOAD

CHARGE

FAN

MPC

A0

C0

B0

B1

B2

B3

D0

D1

F0

E0

E1

E2

E3

LEDs E0 – E3 provide a visual representation of the output voltage level. When the output voltage

is close to the nominal (Vset), all four LEDs will be illuminated green. When the output voltage is

below 21 V, LED E0 will be amber and E1‑E3 will be off.

«
...
28
29
30
31
32
...
»

Содержание 1250













































Отзывы:

Нет отзывов