MPC 1250 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 44

MPC 1250 Скачать руководство пользователя страница 33

Section V

Multiple MPC Configurations

006-0007207 MPC-1250DC Guide

Rev F

33 of 44

03/03/2022

www.synqor.com

Configuration Cables

Configuration cables are necessary for paralleling. They provide the following features:

• Synchronized start up, shut down, and fault recovery
• Digital communication for load sharing
• Up to 32 units in parallel.

The table below lists configuration cables for systems of 2‑5 units. Contact the factory for

configuration cables that support more than five units in parallel.

Configuration Cables for Paralleling

2 Units Parallel, 3'

SYN‑9341

3 units parallel, 6'

SYN‑9343

4 units parallel, 9'

SYN‑9344

5 units parallel, 12'

SYN‑9345

On/Off control – Parallel Systems

When several units are connected in parallel, any “on” front panel switch actuation will cause

all outputs to turn on at once. In addition, the “remote‑on” rear panel signal can be used for a

coordinated start. Any “off” front panel switch actuation will cause that specific unit be turned

off. All other units will continue to deliver power, assuming the load can be supported with one

less unit. In addition, the “remote‑on” or “remote‑off” rear panel signal inputs may be utilized

to enable and disable one specific unit.

For coordinated shutdown, the user must send “SYSTEM DISABLE” over RS‑232. See Section V of

the Owner’s guide for details on the RS‑232 interface. See the UPS User Commands document

for more information on the “SYSTEM DISABLE” command.

«
...
31
32
33
34
35
...
»

Содержание 1250













































Отзывы:

Нет отзывов