MPC 1250 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 44

MPC 1250 Скачать руководство пользователя страница 38

006-0007207 MPC-1250DC Guide

Rev F

38 of 44

03/03/2022

www.synqor.com

Section VII

Maintenance

Fans

The fans on the rear panel have sealed bearings that do not require any maintenance. Fan

assemblies are user replaceable with kits available from SynQor. Please contact the SynQor

factory for obtaining fan replacement kits.

Cleaning

The MPC‑1250 unit has a sealed chamber for its electronics that is weather‑proof. Only the

fans on the rear panel are exposed to the environment, and these fans are also weather‑proof.

The unit can therefore be cleaned without concern of getting liquids inside the chamber. NOTE,

however, that if the cables have been removed from the connectors the connectors should have

their covers installed. If they are not, then care should be taken to not get excess liquid on the

connector terminals. ALSO NOTE that care should be taken to not get excess liquid on the switch

of the AC BREAKER on the back panel.

Cleaning should be done either with soap and water or with an Isopropyl alcohol and water

mixture. A soft cloth should be used.

Do not immerse the unit in water to clean it.

«
...
36
37
38
39
40
...
»

Содержание 1250













































Отзывы:

Нет отзывов