MPC 1250 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 44

MPC 1250 Скачать руководство пользователя страница 22

Section III

Operation

006-0007207 MPC-1250DC Guide

Rev F

22 of 44

03/03/2022

www.synqor.com

Front Panel Indicators

To indicate the status of the MPC, there is one LED above the ON/OFF switch on the left side of

the front panel of the MPC and an additional 10 LEDs on the front panel. There is also an audible

alarm. These indicators are described in this section.

LEDs

LED above the ON/OFF switch

This LED has four possible indications, according to the table below:

LED Appearance

Description

Indication

Green

MPC is Running

(Outputs are Enabled)

Amber

MPC is on Standby

(Outputs are Enabled)

Red

MPC has a Fault Condition

Off

MPC is Off

LEDs on the Front Panel - “Regulated” and “Parallel” Models

The “Regulated” and “Parallel” models each have a 10 LED front panel display to indicate the status

and operation of the MPC. LED A1 is permanently disabled. There is no AC outlet on the unit.

A0

A1

C0

D0

D1

F0

B0

B1

B2

B3

«
...
20
21
22
23
24
...
»

Содержание 1250













































Отзывы:

Нет отзывов