Motrona FM210 Скачать руководство пользователя

Страница: 21 / 40

Fm210_01b_oi_e.docx / Nov-20

Page 21 / 40

Trim+/-

The Trim+/- function continuously adds or subtracts increments into the differential counter and thus
ensures that the output runs away, for example for a position shifting to the master drive. The time per

added or subtracted pulse is indicated by the Trim Speed parameter. A setting of zero executes this

in minimum time (loop time). This command is similar to Offset Edge.

Trim pulses are saved in an internal Trim Counter Register and can be read out. (code position :4).

The internal Trim Counter Register can be reset by using the Reset Edge command (setting Special

Mode = 1).

Trim+:

Triggering Parameter

Comment

Addition

Input

Input X Config = 0/1
Input X Function = 7

If Input X Config = 0 is set, the command is
triggered in case of a "low" state at input X.

The status of the input can be
read in the OS Input field

Lecom

Code 65 (dec)

Release: 04 31 31 02 36 35 30 03 30

Set: 04 31 31 02 36 35 31 03 31
(Unit no. 11, command in hex)

If a 1 is written at code 65, the

command is set.

Modbus

FF0C (hex)

Release: 07 06 FF 0C 00 00 79 BB

Set: 07 06 FF 0C 00 01 B8 7B
(Modbus address = 7, command in hex)

If a 1 is written to FF0C, the

command is set.

Trim-:

Triggering Parameter

Comment

Addition

Input

Input X Config = 0/1

Input X Function = 8

If Input X Config = 0 is set, the command is

triggered in case of a "low" state at input X.

The status of the input can be

read in the OS Input field

Lecom

Code 66 (dec)

Release: 04 31 31 02 36 36 30 03 33
Set: 04 31 31 02 36 36 31 03 32

(Unit no. 11, command in hex)

If a 1 is written at code 66, the
command is set.

Modbus

FF0E (hex)

Release: 07 06 FF 0E 00 00 D8 7B
Set: 07 06 FF 0E 00 01 19 BB
(Modbus address = 7, command in hex)

If a 1 is written to FF0E, the
command is set.

Attention:

If too many increments per time are added or subtracted and the closed

loop control is not able to follow, the differential counter may run away. The

closed loop control or the affected parameters have to be adjusted in a way

that this does not happen. Alternatively, the differential counter must be

reset afterwards (Reset Edge)

Also note the settings for the output phase error, because the differential

counter is modified during trim operation.

Содержание FM210









































Результаты поиска

Содержание FM210

Отзывы:

Похожие инструкции для FM210

Бренды по названию

Популярные бренды

Motrona FM210, Руководство по эксплуатации

Результаты поиска

Содержание FM210

Отзывы:

Похожие инструкции для FM210

Бренды по названию

Популярные бренды