Motorola NVG510 Скачать руководство пользователя страница 125

Страница: 125 / 152

125

set voip phone

sip-advanced-setting sip-qos-p-bit-value [ 0 - 7 ]

Sets a QoS P-bit value for the SIP session. Default is

set voip phone

sip-advanced-setting sip-qos-marker-value

value

Sets a QoS marker on the SIP session packets on the specified phone line.

set voip phone

sip-advanced-setting rtp-qos-tos-value [ 0 - 255 ]

Specifies the RTP Diff-Serv Type of Service (ToS) values for Quality of Service (QoS) assignment. Default is

184

set voip phone

sip-advanced-setting rtp-qos-p-bit-value [ 0 - 7 ]

Sets a QoS P-bit value for the RTP session. Default is

set voip phone

sip-advanced-setting rtp-qos-marker-value

value

Sets a QoS marker on the RTP session packets on the specified phone line.

set voip phone

sip-advanced-setting fax-redundancy-level [ 0 - 1 ]

Specifies the level of fax redundancy for t38 fax data rate management.

set voip phone

sip-advanced-setting sip-init-de-register [ off | on ]

Turns SIP de-registration on or off. Default is

off

set voip phone

sip-advanced-setting sip-known-ip-list

string

Specifies a known IP address list of SIP servers for the SIP session.

Advanced telephony settings

The telephony features include advanced settings for fine tuning phone behavior. The following codecs and asso-
ciated

value

defaults are supported:

Codec G711U

Codec G711A

Codec G729

Codec G726_16

packetization-time

jitter-max-reorder-delay

jitter-max-accept-late-seq-
num

200

jitter-initial-delay

jitter-exe-frame-del-mode

off

jitter-max-transit-delay

250

jitter-peak-transit-delay

475

jitter-delay-buff-inc

jitter-transit-delay-threshold

10000

Содержание NVG510

























































































































































Результаты поиска

Содержание NVG510

Отзывы:

Похожие инструкции для NVG510

Бренды по названию

Популярные бренды

Motorola NVG510, Руководство администратора

Результаты поиска

Содержание NVG510

Отзывы:

Похожие инструкции для NVG510

Бренды по названию

Популярные бренды