Motorola NVG510 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 152

background image

Administrator’s Handbook

110

Application Layer Gateway (ALG) commands

These commands allow you to enable or disable the router’s support for a variety of Application Layer Gateways
(ALGs). An application layer gateway (ALG) is a NAT component that helps certain application sessions to pass
cleanly through NAT. Each ALG has a slightly different function based on the particular application’s protocol-spe-
cific requirements.
An internal client first establishes a connection with the ALG. The ALG determines if the connection should be
allowed or not and then establishes a connection with the destination computer. All communications go through
two connections – client to ALG and ALG to destination. The ALG monitors all traffic against its rules before decid-
ing whether or not to forward it. The ALG is the only address seen by the public Internet so the internal network is
concealed. In some situations, it may be desirable to disable some of the ALGs.

set ip alg esp-enable [ on | off ]

Turns the ESP (Encapsulated Security Payload) ALG for file transfers

on

or

off

. Default is

on

.

set ip alg esp-setup-timeout

value

Specifies the timeout value for the ESP ALG setup. Default is

180

.

set ip alg esp-stream-timeout

value

Specifies the timeout value for the ESP ALG streaming. Default is

300

.

set ip alg ftp-enable [ on | off ]

Turns the FTP (File Transfer Protocol) ALG for file transfers

on

or

off

. Default is

on

.

set ip alg h323-enable [ on | off ]

Turns the H323 ALG for audio, video, and data communications across IP-based networks

on

or

off

. Default is

on

.

set ip alg pptp-enable [ on | off ]

Turns the PPTP (Point-to-Point Transfer Protocol) ALG for authentication

on

or

off

. Default is

on

.

set ip alg sip-enable [ on | off ]

Turns the SIP (Session Initiation Protocol) ALG for voice communication initiation

on

or

off

. Default is

on

.

set ip alg tftp-enable [ on | off ]

Turns the TFTP (Trivial File Transfer Protocol) ALG for simple file transfers and firmware updates

on

or

off

.

Default is

on

.

Dynamic DNS Commands

set ip dynamic-dns enable [ off | on ]

Enables or disables Dynamic DNS. Dynamic DNS support allows you to use the free services of www.dyndns.org.
Dynamic DNS automatically directs any public Internet request for your computer's name to your current dynami-
cally-assigned IP address. This allows you to get to the IP address assigned to your Gateway, even though your
actual IP address may change as a result of a PPPoE connection to the Internet.

«
...
108
109
110
111
112
...
»

Содержание NVG510

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для NVG510

Intesis IN701-KNX Series

Бренд: HMS Networks Страницы: 48

SmartNode SN4150

Бренд: Patton Страницы: 80

Бренд: Dispel Страницы: 17

Бренд: MatchX Страницы: 20

Бренд: Sagem Страницы: 27

Бренд: Artila Страницы: 22

Бренд: ANTIFERENCE Страницы: 26

Бренд: NETGEAR Страницы: 7

Бренд: IC nexus Страницы: 36

Бренд: NKE Страницы: 14

Бренд: WePresent Страницы: 39

Бренд: Planet Networking & Communication Страницы: 2

DTT PRI GSM CDMA Ingate

Бренд: Discovery Telecom Страницы: 57

Бренд: Comcast Страницы: 5

Бренд: Exegin Страницы: 84

Бренд: ZyXEL Communications Страницы: 35

Бренд: ActionTec Страницы: 127

Бренд: ZyXEL Communications Страницы: 296

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды