Motorola NVG510 Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 152

background image

101

set queue name

queue_name

entry

number

input

queue_name

Sets the input to a priority or weighted fair queue.

set queue name

queue_name

entry

number

marker

queue_marker

Sets the marker with which packets must be marked to be directed to this queue entry's input queue when the
type is

priority

or

wfq

.

set queue name

queue_name

entry

number

priority [ 0... 255 ]

Sets the priority level of this queue. A lower value indicates a higher priority. All entries of equal priority will be sub-
ject to a round robin algorithm.

◆

for (strict)

priority

queue, the higher priority gets link resource first.

◆

for

wfq

queue, each entry gets reserved bandwidth according to its weight. If different priority is given, any

excess bandwidth is offered to higher priority entry first; otherwise any excess bandwidth is distributed to the
weights ratio.

set queue name

queue_name

entry

number

weight [ 0... 100 ]

Sets the weight level of this weighted fair queue. Weight units are dependent on

bps-mode

setting.

◆

If

bps-mode

is set to

bps

, then setting the weight to 0 will allocate the remaining available bandwidth to the

queue entry.

◆

If no priority specified, excess bandwidth will be distributed proportionately to the weight ratio.

set queue name

queue_name

default-entry

queue_name

Indicates the input queue which is used if there is no match between the packet queue marker and the configured
markers in any of the queue's inputs when the queue type is

priority

or

wfq

.

IP Gateway commands

set ip gateway enable [ on | off ]

Specifies the

conn

of the gateway. Normally, this would be the WAN connection.

Specifies whether the Motor-

ola Gateway should send packets to a default Gateway if it does not know how to reach the destination
host.

set ip gateway conn-oid

value

Sets the

default Gateway

to point to an associated link specified by the

conn-oid

value.

set ip gateway address

ip_address

Specifies the IP address of a host on a local or remote network in standard dotted-quad format.

IPv6 Commands

set ip6 enable [ on | off ]

Enables/disables IPv6 globally.

«
...
99
100
101
102
103
...
»

Содержание NVG510

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для NVG510

WAGO 750-8212/000-100

Бренд: Viessmann Страницы: 36

EU5C-SWD-ETHERCAT

Бренд: hilscher Страницы: 98

Catalyst 8200 Series

Бренд: Cisco Страницы: 8

Бренд: SpectraLink Страницы: 35

CloudGate-mini Wi-Fi

Бренд: Carel Страницы: 2

Бренд: SAE Страницы: 17

Бренд: Xtream Страницы: 9

Busch-free@home DG-M-1.16.11

Бренд: Busch-Jaeger Страницы: 35

Бренд: Rosonix Technology Страницы: 16

TotalStorage NAS Gateway 500

Бренд: IBM Страницы: 358

Бренд: Shenzhen Sailwider Electronics Co., Ltd. Страницы: 15

Бренд: IQ Home Страницы: 15

Бренд: Yeastar Technology Страницы: 20

Бренд: Yeastar Technology Страницы: 11

SmartZone EPA126

Бренд: Panduit Страницы: 20

WisGate Edge Max

Бренд: RAK Страницы: 20

Бренд: Oki Страницы: 344

Бренд: IQRF Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды