Motorola NVG510 Скачать руководство пользователя страница 124

Страница: 124 / 152

Administrator’s Handbook

124

set voip phone

codec G726_24 priority [ 1 | 2 | 3 | 4 | 5 | 6 | 7 | none ]

Assigns a priority to the

G726-24

codec, a common audio media type implementation at 24 kbit/s.

set voip phone

codec G726_32 priority [ 1 | 2 | 3 | 4 | 5 | 6 | 7 | none ]

Assigns a priority to the

G726-32

codec, a common audio media type implementation at 32 kbit/s.

set voip phone

codec G726_40 priority [ 1 | 2 | 3 | 4 | 5 | 6 | 7 | none ]

Assigns a priority to the

G726-40

codec, a common audio media type implementation at 40 kbit/s.

Advanced settings

set voip phone

sip-advanced-setting sip-dtmf-mode [ inband | rfc2833 | info ]

sip-dtmf-mode

– sets the Dual Tone Multi-Frequency Mode:

◆

inband

: sends the DTMF digits as a normal inband tone.

◆

rfc2833

: (default) sends the DTMF digits as an event as part of the RTP packet header

information.

◆

info

: sends the DTMF digits in the SIP INFO message.

set voip phone

sip-advanced-setting sip-hk-flash-mode [ cpe | info ]

Sets the behavior of the flash hook mode for the specified phone line. Default is

info

set voip phone

sip-advanced-setting sip-session-refresher

[ local | remote | auto ]

Sets the method for refreshing the SIP session. Default is

auto

set voip phone

sip-advanced-setting sip-dynamic-payload [ 96 - 110 ]

Specifies a default dynamic payload value for a named telephony event. Default is

101

set voip phone

sip-advanced-setting sip-digit-map

string

Specifies rules used to recognize a number dialed by the user and to ensure this number matches the
dial plan defined by the ITSP.

set voip phone

sip-advanced-setting sip-compact-header [ off | on ]

Forces all headers in the message to use compact format when set to

. Sends the SIP messages with Compact

Headers, reducing the size of the SIP messages.

set voip phone

sip-advanced-setting sip-q-value [ 0 - 10 ]

This is used to prioritize the SIP account based on the value.

set voip phone

sip-advanced-setting sip-qos-tos-value [ 0 - 255 ]

Specifies the SIP Diff-Serv Type of Service (ToS) values for Quality of Service (QoS) assignment. Default is

136

Содержание NVG510

























































































































































Результаты поиска

Содержание NVG510

Отзывы:

Похожие инструкции для NVG510

Бренды по названию

Популярные бренды

Motorola NVG510, Руководство администратора

Результаты поиска

Содержание NVG510

Отзывы:

Похожие инструкции для NVG510

Бренды по названию

Популярные бренды