Motorola NVG510 Скачать руководство пользователя страница 29

Страница: 29 / 152

Gateway IPv4 Address

Your ISP's gateway router IP address.

MAC Address

Your Gateway’s unique hardware address identifier.

Primary DNS

The IP Address of the Primary Domain Name Server.

Secondary DNS

The IP Address of the backup Domain Name Server, if available.

Primary DNS Name

The name of the Primary Domain Name Server.

Secondary DNS Name

The name of the backup Domain Name Server, if available.

MTU

Maximum Transmittable Unit before packets are broken into multiple packets.

IPv6

Status

May be

Enabled

Disabled

Global Unicast IPv6
Address

The public IPv6 address of your device, whether dynamically or statically
assigned.

Border Relay IPv4
Address

The public IPv4 address of your device.

IPv4 Statistics

Transmit Packets

IPv4 packets transmitted.

Transmit Errors

Errors on IPv4 packets transmitted.

Transmit Discards

IPv4 packets dropped.

Downstream and Upstream Statistics

SN Margin (db)

Signal to noise margin, in decibels. Reflects the amount of unwanted “noise”
on the DSL line.

Line Attenuation

Amount of reduction in signal strength on the DSL line, in decibels.

Output Power (dBm)

Measure of power output in decibels (dB) referenced to one milliwatt (mW).

Errored Seconds

The number of uncorrected seconds after being down for seven consecutive
seconds.

Loss of Signal

The absence of any signal for any reason, such as a disconnected cable or
loss of power.

Loss of Frame

A signal is detected but cannot sync with signal caused by mismatched proto-
cols, wrong ISP connection configuration, or faulty cable.

FEC Errors

(Forwarded Error Correction errors) Count of received errored packets that
were fixed successfully with out a retry.

CRC Errors

Number of times data packets have had to be resent due to errors in transmis-
sion or reception.

Содержание NVG510

























































































































































Результаты поиска

Содержание NVG510

Отзывы:

Похожие инструкции для NVG510

Бренды по названию

Популярные бренды

Motorola NVG510, Руководство администратора

Результаты поиска

Содержание NVG510

Отзывы:

Похожие инструкции для NVG510

Бренды по названию

Популярные бренды