Motorola NVG510 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 152

background image

33

The links at the top of the Home Network page access a series of pages to allow you to configure and
monitor features of your device. The following sections give brief descriptions of these pages.

◆

“Configure” on page 34

◆

“Wireless” on page 35

◆

“WPS” on page 39

◆

“MAC Filtering” on page 40

◆

“Subnets & DHCP” on page 41

ERP-PBCC Status

This tells whether or not the Gateway is honoring legacy 802.11b compatibility
mode.

DSSS-OFDM Status

This is the wireless modulation in use. DSS if in

b-only

mode, OFDM other-

wise.

MAC Address Filtering

May be either

On

or

Off

. If On, you can accept or block client devices from

your WLAN based on their MAC address.

Power Level

May be adjusted up to 100%, lower if multiple wireless access points are in
use, and might interfere with each other.

Key Management Infor-
mation

Shows the information of the security encryption key in use.

LAN Wireless Statistics

Bytes Transmitted

Number of bytes transmitted on the Wi-Fi network.

Bytes Received

Number of bytes received on the Wi-Fi network.

Packets Transmitted

Number of packets transmitted on the Wi-Fi network.

Packets Received

Number of packets received on the Wi-Fi network.

Error Packets Transmitted

This is the number of errors on packets transmitted on the Wi-Fi network.

Error Packets Received

This is the number of errors on packets received on the Wi-Fi network.

Discard Packets Transmit-
ted

This is the number of packets transmitted on the Wi-Fi network that were
dropped.

Discard Packets Received

This is the number of packets received on the Wi-Fi network that were
dropped.

LAN Ethernet Statistics

State

up

or

down

Transmit Speed

This is the maximum speed of which the port is capable.

Transmit Packets

This is the number of packets sent out from the port.

Transmit Bytes

This is the number of bytes sent out from the port.

Transmit Dropped

This is the number of packets sent out from the port that were dropped.

Transmit Errors

This is the number of errors on packets sent out from the port.

Receive Packets

This is the number of packets received on the port.

Receive Bytes

This is the number of bytes received on the port.

Receive Unicast

This is the number of unicast packets received on the port.

Receive Multicast

This is the number of multicast packets received on the port.

Receive Dropped

This is the number of packets received on the port that were dropped.

Receive Errors

This is the number of errors on packets received on the port.

«
...
31
32
33
34
35
...
»

Содержание NVG510

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для NVG510

Бренд: Patton Страницы: 181

Бренд: Eaton Страницы: 2

Бренд: Pace Страницы: 2

Бренд: Extron electronics Страницы: 23

Бренд: M-system Страницы: 7

Бренд: QUNDIS Страницы: 48

Бренд: Edimax Страницы: 27

Бренд: PTT Страницы: 21

KoolKey EKA 200

Бренд: Danfoss Страницы: 2

Бренд: Valcom Страницы: 4

Бренд: RFM Страницы: 31

Бренд: CALEFFI Страницы: 20

Бренд: Tadiran Telecom Страницы: 89

Бренд: t.a.c. Страницы: 4

Бренд: Vaisala Страницы: 32

Бренд: Vaillant Страницы: 40

Бренд: Pahlen Страницы: 19

Бренд: Kaon Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды