manualshive.com logo in svg

Morningstar TriStar MPPT 600V, Инструкция по установке и эксплуатации

Поделиться
Скачать
Morningstar TriStar MPPT 600V Скачать руководство пользователя страница 48

48

Operation

Temperature Compensation

All charging settings are based on 25°C  (77°F).  If the battery temperature varies by 5°C, the 
charging setting will change by 0.60 Volts for a 48 Volt battery.  This is a substantial change in 
the charging of the battery, and the use of the Remote Temperature Sensor (RTS) is recom-
mended to adjust charging to the actual battery temperature.  

The need for temperature compensation depends on the temperature variations, battery type, 
how the system is used, and other factors.  If the battery appears to be gassing too much or not 
charging enough, the RTS can be added at any time after the system has been installed.  See 
Section 3.4 - Step 7 for installation instructions.

Battery Sense

Voltage drops are unavoidable in power cables that carry current, including the 
TS-MPPT-600V-TR battery cables.  If Battery Sense wires are not used, the controller must use 
the voltage reading at the battery power terminals for regulation. Due to voltage drops in the 
battery cables, the battery power connection voltage will be higher than the actual battery bank 
voltage while charging the battery.

Two sense wires, sized from 1.0 to 0.25 mm

2

 (16 to 24 AWG), can be used for battery voltage 

sense.  Because these wires carry no current, the voltage at the TriStar will be identical to the 
battery voltage.  A 2-position terminal is used for the battery sense connection.

Generally accepted wiring practice is to limit voltage drops between the charger and the battery 

to 2%. Even properly sized wiring results in significant voltage drop that can impact charging. The 

controller will begin Absorption or limit equalization at a lower battery voltage because the volt-
age at the controller’s terminals is higher than the actual battery voltage.  

Note that the battery sense wires will not power the controller, and the sense wires will not com-
pensate for losses in the power wires between the controller and the battery.  The battery sense 
wires are only used to improve the accuracy of the battery charging.

See Section 3.4 - Step 8 for instructions on how to connect the battery sense wires.

4.4 GFPD-600V Operation 

Refer to the included GFPD-600V product manual for complete operating information.

Ground-Fault Detection:

Ground-fault protection is used in electrical systems to prevent current from following any unintended 
paths.  It is critical to detect any stray current, and to interrupt (break) the circuit until safe operation 
can be restored.

Any current imbalance between the (+) and (-) conductors of a circuit indicates a ground-fault.  
Morningstar’s GFPD-600V will detect this condition, and break the circuit on both the (+) and (-) 
legs, ensuring interruption.

Содержание TriStar MPPT 600V






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды