manualshive.com logo in svg

MORLEY-IAS FW9003 Range, Руководство по установке

Поделиться
Скачать
MORLEY-IAS FW9003 Range Скачать руководство пользователя страница 25

 
ZX Fire Alarm Control Panels 

 

MORLEY-IAS 

 

Installation Manual 

Document No. 996-174-000-1, Revision: 01 

Page 21 

3.4.7  Panel Networking / Graphics PC Interface 

EN54

!

 

EN54-2 12.5 

Integrity of 
transmission paths: 

The network does 
not provide the 
required 
transmission path 
integrity. 

The Panel Network (Master to Slave panel) interface uses Port ‘C’ 
position on the base card. 

A Master Panel (ZX5Se and ZX10Se only) can also be connected 
either to a Superior Master or to a Graphics PC using the Port ‘B’ 
position on the base card. 

3.4.7.1 

Local Panel Network 

The ZX1Se, ZX2Se, ZX5Se and ZX10Se Fire Alarm Control Panels can be connected in a 
network of panels with other panels in the ZX Series FACP range. 

The panels can be connected in two types of configuration: A Shared Zone Network in which 
panels share common zones and function as one system; a Report and Control Network in which 
individual panels or subsystems are networked for reporting and control purposes only. 

A panel network requires the installation of an Isolated RS485 Interface card in each panel, using 
the Port ‘C’ interface position. 

For detailed information on networking and wiring installation for a panel network, refer to 
document P/N 996-075. 

3.4.7.2 

Master Panel to Superior Master Panel 

The network can be further extended, by connecting Network Master Panels to a Superior 
Master Panel (ZX5Se and ZX10Se only). 

The network master panels are connected via an Isolated RS485 Interface Card in the Port ‘B’ 
position to the Superior Master panel containing an Isolated RS485 Interface Card in the Port ‘C’ 
position. 

For detailed information on networking and wiring installation for a panel network, refer to 
document P/N 996-075. 

3.4.7.3 

Panel to Graphics PC 

A Network Master panel or a Superior Master Panel may be connected to a Graphics PC for 
additional reporting and control purposes (ZX5Se and ZX10Se only). 

The Graphics PC interface requires the installation of either an Isolated RS232 interface or an 
Isolated RS485 interface card using the Port ‘B’ position. 

The ZX1Se and ZX2Se panel may be connected to a Graphics PC but may then not be 
connected in a network of panels. 

For detailed information on connecting and using a Graphics PC, refer to documents P/N 996-
046 and 996-047. 

 

Содержание FW9003 Range
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды