background image

Improper transport

 NOTICE!

Damage to property due to improper
transport!

Transport units may fall or tip over as a

result of improper transport. This can

cause a significant level of property

damage.

– Proceed carefully when unloading

transport units at delivery and during

in-house transport; observe the sym-

bols and instructions on the packaging.

– Only use the attachment points pro-

vided.

– Only remove the packaging shortly

before assembly.

5.2  Inspection on receipt of delivery

On receipt, immediately inspect the delivery for

completeness and transport damage.

Proceed as follows in the event of externally appa-

rent transport damage:

n

Do not accept the delivery, or only accept it

subject to reservation.

n

Note the extent of the damage on the transport

documentation or the shipper's delivery note.

n

Initiate complaint procedures.

Issue a complaint in respect of each defect

immediately following detection. Damage

compensation claims can only be asserted

within the applicable complaint deadlines.

5.3  Packaging

About packaging

The individual packages are packaged in accord-

ance with anticipated transport conditions. Only

environmentally-friendly materials have been used

in the packaging.

The packaging is intended to protect the individual

components from transport damage, corrosion and

other damage prior to assembly. Therefore do not

destroy the packaging and only remove it shortly

before assembly.

Handling of packaging materials

Either keep packaging material for a later dispatch

or storage the device or dispose of it in accord-

ance with the valid local regulations legal provi-

sions and local regulations.

 NOTICE!

Risk of environmental damage from
incorrect disposal!

Packaging materials are valuable raw

materials and can in many cases be used

again or prepared sensibly and recycled.

Incorrect disposal of packaging materials

can cause environmental hazards.

– Dispose of packaging materials in an

environmentally-friendly fashion.

– Heed the local disposal regulations.

Have disposal carried out by a spe-

cialist company as necessary.

5.4  Symbols on the packaging

The following symbols may be affixed to the pack-

aging. Always adhere to the symbols during trans-

portation.

Attach here

Only use means of attachment (chain sling, lifting

strap) in the places marked with this symbol.

Rotopack • Operating instructions

 

 

16

Содержание GAT Rotopack BAT




























Отзывы: