Monosem NG Plus 2 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 76

Monosem NG Plus 2 Скачать руководство пользователя страница 36

Maintenance

34

MARKER BEARING LUBRICATION OR
REPLACEMENT

1.  Remove marker blade.
2.  Remove dust cap from hub.
3.  Remove cotter pin, nut and washer.
4.  Slide hub from spindle.
5.  Remove bearings and cups and discard

if bearings are being replaced. Clean hub
and dry. Remove bearings only and not
cups if repacking.

6. Press in new bearing cups with thickest

edge facing in. (Bearing replacement
procedure only.)

7. Pack bearings with heavy duty wheel

bearing grease thoroughly forcing grease
between roller cone and bearing cage.
Also fill the space between the bearing
cups in the hub with grease.

8. Install rubber seal into grease seal. Place

inner bearing in place and press in new
rubber seal/grease seal.

9. Clean spindle and install hub.
10. Install outer bearing, washer and slotted

hex nut. Tighten slotted hex nut while
rotating hub until there is some drag.
This assures that all bearing surfaces are
in contact. Back off slotted nut to nearest
locking slot and install cotter pin.

11. Fill dust caps approximately 3/4 full of

wheel bearing grease and install on hub.

12. Install blade and dust cap retainer on

hub and tighten evenly and securely.

WHEEL BEARING LUBRICATION OR
REPLACEMENT

1. Raise tire clear of ground and remove

wheel.

2. Remove double jam nuts and slide hub

from spindle.

3. Remove bearings and cups and discard

if bearings are being replaced. Clean hub
and dry. Remove bearings only and not
cups if repacking.

4. Press in new bearing cups with thickest

edge facing in. (Bearing replacement
procedure only.)

5. Pack bearings with heavy duty wheel

bearing grease thoroughly forcing grease
between roller cone and bearing cage.
Also fill the space between the bearing
cups in the hub with grease.

6.  Place inner bearing in place.
7.  Clean spindle and install hub.
8.  Install outer bearing and jam nut. Tighten

jam nut while rotating hub until there is
some drag. This assures that all bearing
surfaces are in contact. Back off jam nut
1/4 turn or until there is only slight drag
when rotating the hub. Install second jam
nut to lock against first.

9. Install wheel on hub and tighten evenly

and securely.

http://hespareparts.com

«
...
34
35
36
37
38
...
»

Содержание NG Plus 2













































































Отзывы:

Нет отзывов