Monosem NG Plus 2 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 76

Monosem NG Plus 2 Скачать руководство пользователя страница 30

Lubrication

28

The following pages show the locations of all
lubrication points. Proper lubrication of all
moving parts will help ensure efficient
operation of your MONOSEM planter and
prolong the life of friction producing parts.

DANGER : Always install safety

lockups or lower to the ground before
working under the machine.

LUBRICATION SYMBOLS

Lubricate at frequency indicated with an SAE
multipurpose type grease.

Lubricate at frequency indicated with a high
quality SAE 10 weight oil or a quality spray
lubricant.

DRIVE CHAINS

All transmission and drive chains should be
lubricated daily with a high quality SAE 10
weight oil or a quality spray lubricant.
Extreme operating conditions such as dirt,
temperature or speed may require more
frequent lubrication. If a chain become stiff, it
should be removed, soaked and washed in
solvent to loosen and remove dirt from the
joints. Then soak the chain in oil so the
lubricant can penetrate between the rollers
and bushings.

Contact drive chain

Jack shaft chain

Weekly

Daily

W eekly

Daily

!

http://hespareparts.com

«
...
28
29
30
31
32
...
»

Содержание NG Plus 2













































































Отзывы:

Нет отзывов