Moffat Turbofan G32MS Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 70

Moffat Turbofan G32MS Скачать руководство пользователя страница 66

-66-

Revision 6/F3590

©

Moffat Ltd, February 2005

Contents:

2 Side Cover (1)

1 Front Panel (2)

2 Side Support Rail (3)

1 Rear Panel (4)

1 Flue Duct (5)

1 Chimney (6)

1 Chimney Support (7)

31 Screws 8x3/8”

4 3/8” x 3/4” Bolts and Washers

NOTE:

Food Grade RTV Silicone Sealant not supplied with kit

Instructions:

Bottom Unit

NOTE:

Refer to figure C. (overleaf) for general layout of stacking kit.

1) Remove the six middle screws from top rear of bottom unit.
2) Unscrew the vent hood plate from the bottom oven. Remove and discard the hood plate and

spacer tubes. Replace the vent hood screws and completely screw in to secure the wrapper
to the spacer tube.

3) Temporarily fit rear panel (4) and flue duck (5) to bottom unit (refer figure C), using two of the

existing screw holes at top rear of unit.

4) Place the two side support rails (3) on the unit, ensure the large holes face up.
5) Fasten side support rails (3) to rear panel (4) two screws either side, ensure screws are

started from rear panel (4) side with screw tip pointing out (refer figure A).

6) Remove plastic from front panel (2). Fasten to side support rails (3) (two screws either side),

ensure screw tips point in (refer figure B).

7) Ensure stacking frame is square and mark the positions of the two bottom holes in the front

panel (2) and the six holes for the flue duct (5).

8) Remove the two screws holding stacking frame and flue duct (5) to rear of bottom unit and

remove frame.

9) Drill the eight holes (Ø3.5mm (1/8”)) as per marked in step 7.
10) Apply a small amount of food grade RTV silicone sealant to the flue duct flanges (5) and screw

to the bottom unit with six screws along the top (drilled), and two at the rear.

11) Re-fit stacking frame, fit three screws at rear and two screws at front into the holes drilled.

CAUTION: ENSURE UNIT IS ISOLATED FROM ELECTRICAL / GAS SUPPLIES

BEFORE SERVICING

Figure A.

Figure B.

Screws

pointing in.

Screws

pointing out.

Rear

Panel.

Side

Support

Rail.

Side

Support

Rail.

Front

Panel.

APPENDIX B. DOUBLE STACKING KIT

(Kits manufactured from March 2004)

«
...
64
65
66
67
68
...
»

Содержание Turbofan G32MS







































































Отзывы:

Нет отзывов