manualshive.com logo in svg

Moffat Turbofan G32MS, Руководство по обслуживанию, Страница: 29 / 70

Поделиться
Скачать
Moffat Turbofan G32MS Скачать руководство пользователя страница 29

-29- 

Revision 6/F3590 

© 

Moffat Ltd, February 2005 

6.1.10   60 MINUTE TIMER NO TIME UP       

INDICATOR 

Indicator faulty 

With the timer in the zero position, check for 
voltage across the indicator light.  If correct, 
then the indicator light is faulty—replace. 
If there is no voltage then check wiring. 

6.1.11  NO TEMPERATURE CONTROL 

(TEMPERATURE OVERRUN) 

Thermostat faulty 

With thermostat in off (vertical) position, the 
heating indicator should be off.  If not then the 
thermostat is faulty—replace. 

6.1.12 SLOW RECOVERY 

Thermostat out of calibration 

Place an accurate digital thermometer probe 
in centre of oven.  Set thermostat to 180°C or 
355°F.  Close the oven door and allow oven 
thermostat to cycle on and off twice.  Record 
oven  centre  temperature  for  the  next         
thermostat on and off cycle.  The thermostat 
should cycle on and off between 165°C and 
195°C or 330°F and 385°F when set to the 
above temperature.  If oven temperature is 
outside these ranges, then the thermostat   
requires recalibration. 

NOTE: 

Thermostat cycling span should be 

±15°C or 27°F 

Indicator faulty 

Check the voltage across the indicator 

 

terminals.  If the voltage is correct then the 
indicator is faulty—replace. 
If there is no voltage then check wiring. 

6.1.13   NO THERMOSTAT HEATING         

INDICATOR 

No power to timer  

Check the voltage at terminal 5 on underside 
of the 180 minute timer. 
Check that one lead of timer motor is con-
nected to terminal five of timer and the other 
lead is connected to neutral of ‘Roast ’n Hold’ 
switch. 
If voltage at terminal 5 is correct and wiring is 
correct then the timer motor is faulty—replace 
timer. 
If there is no power at terminal 5, check for 
power supply at terminal 4 of timer.  If there is 
voltage at terminal 4 and not at terminal 6 with 
timer set, then timer switch is faulty—replace 
timer. 

6.1.14   ROAST TIMER (180 MINUTE) WILL 

NOT TIME DOWN 

Figure 6.1.5 

Terminal 4 

Terminal 1 

Terminal 2 

Terminal 5 

Terminal 3 

Terminal 6 

‘Roast ‘n Hold’ switch faulty 

Check if the switch latches.  If the switch does 
not latch then the switch is faulty—replace. 
With the switch latched, check voltage across 
terminal 1 to terminal 3 or 4.  If there is no 
voltage then check for fault in wiring. 
Check voltage across terminal 2 to terminal 3 
or 4.  If there is no voltage then switch is 
faulty—replace. 

NOTE:   

When the switch is latched, it should 

illuminate if operating correctly. 

If terminal 4 voltage is correct, check relay at 
the base of the control housing behind control 
panel is latched ON.  If relay is ON then check 
wiring. 
If relay is not latched ON when ‘Roast ‘n Hold’ 
switch illuminated then check the voltage 
across terminals 7 and 8 of relay coil (fig 
6.1.3).  If the voltage is correct but the relay is 
in the off position then the relay is faulty—
replace. 
If there is no voltage across 7 and 8 then 
check wiring. 

Содержание Turbofan G32MS







































































Отзывы:

Нет отзывов