manualshive.com logo in svg

Model Shipways Western Mountain Buckboard Wagon, Инструкция по эксплуатации

Поделиться
Скачать
Model Shipways Western Mountain Buckboard Wagon Скачать руководство пользователя страница 24

With the platform assembly still inverted fit and adjust luggage rail so that all flange holes 

2. 

align with their mounting holes on the underside of the platform. Index the front flange 

on the bolt shaft of the rear seat mounting bracket and clamp with small alligator spring 

clamps. Then adjust and add toothpicks to index the corner and end flanges and holes. 

This step may require the use of small needle nose pliers to adjust rail posts or flanges for 

alignment. Once satisfied with fit; prime and paint and then re-fit and glue in place using 

four (4) 3/16” round bolts and small square nuts. Just add/glue two (2) small square nuts to 

the rear seat spring bracket bolts with rail flange in place. Allow glue to completely set and 

true up rails to edges of platform. (See photo 23)

Now with the platform assembly setting upright resting on the reach arms; dry fit the apron 

3. 

rail and seat rail after cleaning and adjusting then prime and paint both. 

The apron hand rail requires two (2) 3/16” and four (4) 3/8” painted round head bolts and 

4. 

six (6) small square nuts. Index/glue the two end flanges with 3/16” bolts into apron holes 

next to the formers and add square nuts. Let the glue set. Note: Insert all bolts from front 

surface of the apron.

Align the hand rail flanges with the four (4) holes and add 3/8” round head bolts with 

5. 

square nuts and glue in place. (See Photo 22) Ream holes with a #55 drill bit if necessary. 

 

Photo 22

Dry fit the seat rail and adjust as needed so that rail flanges align with the holes in the in

-

6. 

side surfaces of the seat walls with the lower holes on the rail flanges. Once satisfied with 

dry fit prime and paint seat rail.

Index four (4) 3/16” painted round head bolts into the lower holes glue and add small 

7. 

square nuts to bolt shafts. If necessary adjust post alignment before glue sets.
Once glue is dry; drill holes with #55 drill bit using the upper flange holes as guide, holes 

8. 

through the side walls. Insert/glue four (4) 3/16” round head bolts and square nuts and glue 

in place. (See Photo 23)

Содержание Western Mountain Buckboard Wagon





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды