MKS 356 Micro-Ion Plus Series Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 76

MKS 356 Micro-Ion Plus Series Скачать руководство пользователя страница 67

Micro-Ion

®

Module Instruction Manual - 356007-GP

67

Appendix A Filament Operation

Table A-1

Micro-Ion Filament Operation Modes

Mode

Description

Automatic

• Filament logic operates filament 1 each time the Micro-Ion gauge turns ON
• If filament 1 becomes inoperable, the Micro-Ion gauge switches to filament 2

Alternating (default for Micro-Ion gauge
with yttria-coated iridium filaments)

• Filament logic alternates between filament 1 and filament 2 each time the

Micro-Ion gauge turns ON

• If a filament becomes inoperable, the module switches to the operable filament
• Default mode for Micro-Ion gauge with yttria-coated iridium filaments

Manual (default for Micro-Ion gauge
with tungsten filaments)

• Filament logic operates filament 1 each time the Micro-Ion gauge turns ON
• If filament 1 becomes inoperable, press the gauge button to turn filament 2 ON

(gauge LED will flash red)

• After the gauge button has been pressed, filament 2 turns ON
• Default mode for Micro-Ion gauge with tungsten filaments

Table A-2

Micro-Ion Gauge, Gauge LED, and Filament States in Automatic or Alternating Mode

Micro-Ion Gauge State

Gauge LED State

Filament State

OFF automatically

Amber

Micro-Ion gauge has automatically turned OFF

OFF and disabled

Flashing amber

Micro-Ion gauge is disabled

ON

Green

• Filament 1 or 2 is ON
• Both filaments are operable

ON

Flashing green

Filament 1 or 2 is inoperable

OFF

Red

Filaments 1 and 2 are inoperable

Table A-3

Micro-Ion Gauge, Gauge LED, and Filament States in Manual Mode

Micro-Ion Gauge State

Gauge LED State

Filament State

OFF automatically

Amber

Micro-Ion gauge has automatically turned OFF

OFF and disabled

Flashing amber

Micro-Ion gauge is disabled

ON

Green

Filament 1 is ON

ON

Flashing green

Filament 2 is ON

OFF

Flashing red

• Filament 1 is inoperable
• Press gauge button to switch to filament 2

OFF

Red

Filaments 1 and 2 are inoperable

«
...
65
66
67
68
69
...
»

Содержание 356 Micro-Ion Plus Series













































































Отзывы:

Нет отзывов