MKS 356 Micro-Ion Plus Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 76

MKS 356 Micro-Ion Plus Series Скачать руководство пользователя страница 17

Installation

Micro-Ion

®

Module Instruction Manual - 356007-GP

17

In

stallation

O

per
a

tion

Maintenance

Before You

Begin

VCR-type fitting

a.

Remove the plastic or metal bead protector cap from the fitting.

b.

If a gasket is used, place the gasket into the female nut.

c.

Assemble the components and tighten them finger-tight.

d.

While holding a back-up wrench stationary, tighten the female nut 1/8
turn past finger-tight on 316 stainless steel or nickel gaskets, or 1/4 turn
past finger-tight on copper or aluminum gaskets.

Do not twist the

module to tighten the fitting

.

ConFlat flange

To minimize the possibility of leaks with ConFlat flanges, use high strength
stainless steel bolts and a new, clean stainless steel with OFHC copper
gasket. Avoid scratching the seal surfaces.

a.

Finger tighten all bolts.

b.

Use a wrench to continue tightening 1/8 turn at a time in crisscross
order (1, 4, 2, 5, 3, 6) until flange faces make contact. Further tighten
each bolt about 1/16 turn.

NW flange

The NW mounting system requires O-rings and centering rings between
mating flanges.

Tighten the clamp to compress the mating flanges together and seal the
O-ring.

Step 4

Assemble and Connect the Cables

Connecting Cables

The cables are user-supplied. Granville-Phillips does not supply cable.

• Use externally shielded cable.

• Connect the wiring to the 9-pin trip point connector and the 15-pin

subminiature D connector. On the User Interface connector, Pin 1 must
be connected to pin 5 for the Micro-Ion gauge to turn ON. See Figure 2-2.

«
...
15
16
17
18
19
...
»

Содержание 356 Micro-Ion Plus Series













































































Отзывы:

Нет отзывов