11
11-73
Grinding of crankshaft
CAUTION
• If the crankshaft pins and journals are ground to
undersizes, be sure to use bearings of corresponding
undersizes.
•
Do not change the center-to-center distance A between the jour-
nal and pin.
A:
57.5
mm
•
Do not change the journal width B and the pin width C.
B:
37
mm
C:
42
mm
•
Finish the fillets D smoothly.
D:
R4 ± 0.2 mm
•
Carry out a magnetic inspection to check for cracks possibly
caused by grinding. Also, check that the hardness of the surface
has not dropped below Shore hardness number (Hs) 75.
•
Replace the crankshaft if defects are evident.
Crankshaft undersize dimensions (Unit: mm)
•
When grinding, turn both the crankshaft and the grinder counter-
clockwise as viewed from the crankshaft front end.
•
When finishing the crankshaft with whetstone or sandpaper, ro-
tate the crankshaft clockwise.
Inspection: Distortion of crankcase top surface
•
If the measurement exceeds the limit, correct the crankcase top
surface with a surface grinder.
CAUTION
• Do not grind the crankcase top surface so much as to com-
promise the correct piston projection.
Undersizes
0.25
0.50
0.75
1.00
Finished journal outside diameter
83.685 to 83.705
83.435 to 83.455
83.185 to 83.205
82.935 to 82.955
Finished pin outside diameter
69.67 to 69.69
69.42 to 69.44
69.17 to 69.19
68.92 to 68.94
Out-of-roundness
0.01 or less
Taper
0.006 or less
+0.0252
–0.075
+0.2
0
+0.2
0
Содержание 6M60-TL
