11-58
Installation procedure
Installation: Flywheel housing
[Installation]
•
Clean the flywheel housing surface where sealant is to be ap-
plied.
•
Apply an even and continuous bead of sealant onto the flywheel
housing surface where the crankcase is to be mounted.
•
Install the flywheel housing onto the crankcase within 3 minutes
following the application. Be careful not to smear the sealant
bead.
CAUTION
• Do not start the engine at least for an hour after the flywheel
housing has been installed.
• If the flywheel housing mounting bolts are subsequently
loosened, be sure to apply sealant again upon reassembly.
[Inspection]
•
While turning the crankshaft, measure the flywheel housing for
any eccentricity at the location indicated in the illustration.
•
If the eccentricity exceeds the limit, reassemble the flywheel.
•
If the eccentricity still exceeds the limit after reassembly, replace
the defective part(s).
Installation: Rear oil seal
•
Clean the rear oil seal surface where sealant is to be applied.
•
Apply an even and continuous bead of sealant on the rear oil
seal as shown in the illustration.
•
Install the rear oil seal onto the flywheel housing within 3 min-
utes following the application. Be careful not to smear the seal-
ant bead.
CAUTION
• Do not start the engine at least for an hour after the rear oil
seal has been installed.
• If the rear oil seal mounting bolts are subsequently loos-
ened, be sure to apply sealant again upon reassembly.
•
Apply engine oil to the rear oil seal lip.
•
Install the rear oil seal onto the flywheel housing ensuring that
the seal is faced in the illustrated direction.
FLYWHEEL
Содержание 6M60-TL
