Mitsubishi Electric PUD-SHWM100VAA, Руководство по обслуживанию

Страница: 72 / 76

72
OCH756
OPERATING PROCEDURE PHOTOS/ FIGURES
4. Disassembling the electrical parts box
(V-type model only)
(1) Remove the electrical parts box. (See Photo 3-1)
(2) Disconnect all the connectors on the controller circuit board.
(3) To remove the controller circuit board, release it from the support.
(4) Remove the cont base front fixing screws (3 for front/ 4 ×
10) to remove the cont base front.
(The cont base front is fixed to the electrical parts box
with a hook on the left side.)
(5) Disconnect all the connectors on the power circuit board.
(6) To remove the power circuit board, remove the power cir-
cuit board fixing screws (4 for front/ 3 x 12, 2 for front/ 4
x 18, and 1 for front/ 4x10), then release the board from
the support.
(7) Remove the reactor (DCL1, DCL2, DCL3) fixing screws (6
for rear/ 4 × 10) to remove the reactor, then disconnect
the connectors on reactor.
(8) Remove the thermistor <Heat sink> (TH8) fixing screws
(2 for front/ 3 × 12) to remove the thermistor <Heat sink>
(TH8).
(9) To remove the heat sink, remove the heat sink duct fixing
screws (6 for front/ 4 × 10), then slide the heat sink duct
sideways to remove the heat sink.
Note 1: When reassembling the electrical parts box, make
sure the wirings are correct.
Photo 4-1 Photo 4-2
Photo 4-3 Photo 4-4
5. Disassembling the electrical parts box
(Y-type model only)
(1) Remove the electrical parts box. (See Photo 3-1)
(2) Disconnect all the connectors on the controller circuit board.
(3) To remove the controller circuit board, release it from the support.
(4) Remove the cont base front fixing screws (3 for front/ 4 ×
10) to remove the cont base front.
(The cont base front is fixed to the electrical parts box
with a hook on the left side.)
(5) Disconnect all the connectors on the noise filter circuit board.
(6) To remove the noise filter circuit board, release it from the support.
(7) Remove the cont base fixing screws (3 for front/ 4 × 10)
to remove the cont base.
(The cont base is fixed to the electrical parts box with a
hook on the left side.)
(8) Disconnect all the connectors on the converter circuit
board. (The converter circuit board is attached to the rear
side of the cont base.)
(9) To remove the converter circuit board, release it from the support.
(10) Disconnect all the connectors on the power circuit board.
(11) To remove the power circuit board, remove the power cir-
cuit board fixing screws (4 for front/ 4 × 14), then release
the board from the support.
(12) Remove the thermistor <Heat sink> (TH8) fixing screws (2
for front/ 3 × 12) to remove the thermistor <Heat sink> (TH8).
(13) Disconnect the connectors on reactor (ACL4), resis-
tor (RS) and capacitor (CK) first, then remove the fixing
screws of reactor, resistor and capacitor (4 for front/ 4 ×
10), and remove reactor, resistor and capacitor.
(14) To remove the heat sink, remove the heat sink duct fixing
screws (6 for front/ 4 × 18), then slide the heat sink duct
sideways to remove the heat sink.
Note 1: When reassembling the electrical parts box, make
sure the wirings are correct.
Photo 5-1 Photo 5-2
Photo 5-3 Photo 5-4
Photo 5-5
Controller circuit board
Cont base front Power circuit board
Reactors
Cont base front
Controller circuit board
Converter circuit board
Power circuit board
Reactor
Resistor
Capacitor
Noise filter circuit board
Thermistor <Heat sink> (TH8)
Heat sink
Cont base
Thermistor <Heat sink> (TH8) Heat sink