Mitsubishi Electric Mr.Slim PUHZ-P100VKA Скачать руководство пользователя страница 68

Страница: 68 / 111

OCH670

<Display function of inspection for outdoor unit>

The blinking patterns of both LED1 (green) and LED2 (red) indicate the types of abnormality when it occurs. Types of

abnormality can be indicated in details by connecting an optional part ‘A-Control Service Tool (PAC-SK52ST)’ to connector

CNM on outdoor controller board.

Check refrigerant pipes for disconnection or leakage.

After the recovery of refrigerant, vacuum dry the whole

refrigerant circuit.

Refer to section “9-6 HOW TO CHECK THE PARTS”.

Check refrigerant circuit for operation.

—

A0~A8

[Display]

(1)Normal condition

(2)Abnormal condition

Unit condition

Outdoor controller board

A-Control Service Tool

LED1 (Green)

LED2 (Red)

Check code

When the power is turned on
When unit stops
When compressor is warming up

When unit operates

Lighted

Lighted
Lighted
Lighted

Not lighted

Indication of the display

Alternately blinking display

Operation mode

Not lighted

Lighted

00, etc.
08, etc.

C5, etc.

Indication

Error

Check

code*

Outdoor controller board

Contents

Inspection method

LED1 (Green) LED2 (Red)
1 blinking 2 blinking

2 blinking 1 blinking

2 blinking

3 blinking

4 blinking

5 blinking

Connector (63H) is open.

Startup time over

Check code is not defined.

Miswiring of indoor/outdoor unit conne-

cting wire, excessive number of indoor

units (4 units or more)

Miswiring of indoor/outdoor unit co-

nnecting wire (converse wiring or di-

sconnection)

Indoor/outdoor unit communication error

(signal receiving error) is detected by in-

door unit.

Indoor/outdoor unit communication error

(transmitting error) is detected by indoor

unit.

Indoor/outdoor unit communication error

(signal receiving error) is detected by

outdoor unit.

Indoor/outdoor unit communication error

(transmitting error) is detected by outdoor

unit.

Remote controller signal receiving

error is detected by remote controller.
Remote controller transmitting error

is detected by remote controller.
Remote controller signal receiving

error is detected by indoor unit.
Remote controller transmitting error

is detected by indoor unit.

Serial communication error

<Communication between outdoor

controller board and outdoor power

board>

<Communication between outdoor

controller board and M-NET P.C. board>

Communication error of M-NET

system

*Check code displayed on the remote controller.

Check if indoor/outdoor connecting wire is connected correctly.

Check if 4 or more indoor units are connected to outdoor unit.

Check if noise entered into indoor/outdoor connecting wire

or power supply.

Re-check error by turning off power, and on again.

Check if connector (63H) on the outdoor controller board is

not disconnected.

Check continuity of pressure switch (63H) by tester.

Check if connector (CN4) on outdoor controller board and

outdoor power board is not disconnected.

Check if there is poor connection of connector on outdoor

controller board(CNMNT and CNVMNT).

Check M-NET communication signal.

Check if remote controller is MA remote controller(PAR-21MAA).

Check if noise entered into transmission wire of remote controller.

Check if noise entered into indoor/outdoor connecting wire.

Re-check error by turning off power, and on again.

Check if connecting wire of indoor unit or remote controller

is connected correctly.

Check if noise entered into transmission wire of remote

controller.

Re-check error by turning off power, and on again.

Check if indoor/outdoor connecting wire is connected correctly.

Check if noise entered into indoor/outdoor connecting wire or

power supply.

Check if noise entered into indoor/outdoor controller board.

Re-check error by turning off power, and on again.

P.33

P.34

(EA)

P.34

(Eb)

P.35

(EC)

P.40

(E8)

P.41

(E9)
P.39

P.40

P.39

P.40

P.41

P.42

P.41

Detailed

reference

page

P.42-

P.45

Continued to the next page

Содержание Mr.Slim PUHZ-P100VKA
















































































































Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Руководство по обслуживанию

Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды