Mitsubishi Electric Mr.Slim PUHZ-P100VKA Скачать руководство пользователя страница 101

Страница: 101 / 111

101

OCH670

12-1-2. PAR-21MAA

Slide

●

Reduces maintenance work drastically.

●

Enables you to check operation data of the indoor and outdoor units by remote controller.

Furthermore, use of maintenance stable-operation control that fixes the operating frequency, allows smooth inspection, even for

inverter models.

<Maintenance mode operation method>

If you are going to use <GUIDE FOR OPERATION CONDITION>, set the airflow to "High" before activating maintenance mode.

●

Switching to maintenance mode

Maintenance mode can be activated either when the air conditioner is operated or stopped.

It cannot be activated during test run.

Note: Maintenance information can be viewed even if the air conditioner is stopped.

Operation mode Compressor information Outdoor unit information Indoor unit information

Confirm

Activate/cancel maintenance mode

■

Remote controller button information

(1) Press the

TEST

button for 3 seconds to switch to maintenance mode.

[Display

]

MAINTENANCE

If stable operation is unnecessary or if you want to check the data with the air conditioner stopped, skip to step (4).

●

Fixed Hz operation

The operating frequency can be fixed to stabilize operation of inverter model.

If the air conditioner is currently stopped, start it by this operation.

(2) Press the

MODE

button to select the desired operation mode.

[Display

]

(3) Press the

FILTER

( ) button to confirm the setting.

[Display

] Waiting for stabilization

Stabilized

After 10 to 20 minutes

Discharge temperature 64°C

Remove the

service panel.

Measure

the intake air

temperature.

Measure the discharge

temperature.

Measure the outside

air temperature.

●Indoor unit ●

●Outdoor unit ●

Smooth Mainte-

nance Function

●

Conventional inspection work

Easy maintenance information (unit)

Compressor

Outdoor unit

Indoor unit

Accumulated operating

Heat exchanger

Intake air

time (

10 hours)

temperature (

)

temperature (

)

Number of ON/OFF

Discharge

Heat exchanger

times (

10 times)

temperature (

)

temperature (

)

Operating

Outside air

Filter operating

current (A)

temperature (

)

time* (Hours)

* The filter operating time is the time that has elapsed since the filter was reset.

HEAT

STABLE MODE

CANCEL

COOL

STABLE MODE

Stable cooling

operation

Stable heating

operation

Stable operation

cancellation

Service

panel

Содержание Mr.Slim PUHZ-P100VKA
















































































































Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Руководство по обслуживанию

Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды