Mitsubishi Electric Mr.Slim PUHZ-P100VKA Скачать руководство пользователя страница 34

Страница: 34 / 111

OCH670

Check code

Abnormal points and detection method

Judgment and action

(6845)

Miswiring of indoor/outdoor unit

connecting wire (converse wiring or

disconnection)

Outdoor controller circuit board can

automatically set the unit number of indoor

units.

Abnormal if the indoor unit number cannot

be set within 4 minutes after power on

because of Miswiring (converse wiring

or disconnection) of indoor/outdoor unit

connecting wire.

(6846)

Startup time over

The unit cannot finish startup process

within 4 minutes after power on.

Case

Contact failure of indoor/

outdoor unit connecting wire

Diameter or length of indoor/

outdoor unit connecting wire is

out of specified capacity.

2 or more outdoor units have

refrigerant address “0” .

(In case of group control)

Noise has entered into power

supply or indoor/outdoor unit

connecting wire.

Contact failure or miswiring of

indoor/outdoor unit connecting

wire

Diameter or length of indoor/

outdoor unit connecting wire is

out of specified capacity.

Defective transmitting receiving

circuit of outdoor controller circuit

board

Defective transmitting receiving

circuit of indoor controller board

Defective indoor power board

2 or more outdoor units have

refrigerant address “0” .

(In case of group control)

Noise has entered into power

supply or indoor/outdoor unit

connecting wire.

Miswiring of indoor/outdoor unit

connecting wire

1. Outdoor controller circuit board can

automatically check the number of

connected indoor units. Abnormal if the

number cannot be checked automatically

due to miswiring of indoor/outdoor unit

connecting wire and etc. after power is

turned on for 4 minutes.

2. Abnormal if outdoor controller circuit

board recognizes excessive number of

indoor units.

Check disconnection or looseness or polarity

of indoor/outdoor unit connecting wire of

indoor and outdoor units.

Check diameter and length of indoor/outdoor

unit connecting wire.

Total wiring length: 80 m

(including wiring connecting each indoor unit

and between indoor and outdoor unit)

Also check if the connection order of flat

cable is S1, S2, S3.

Check the number of indoor units that are

connected to one outdoor unit. (If EA is

detected)

–

Turn the power off once, and on again to

check.

Replace outdoor controller circuit board,

indoor controller board or indoor power

board if abnormality occurs again.

Check if refrigerant addresses (SW1-3 to

SW1-6 on outdoor controller circuit board) are

overlapping in case of group control system.

Check transmission path, and remove the

cause.

The descriptions above,

–

, are common for

EA, Eb and EC.

Contact failure or miswiring of

indoor/outdoor unit connecting

wire

Diameter or length of indoor/

outdoor unit connecting wire is

out of specified capacity.

Excessive number of indoor

units are connected to 1 out-

door unit. (4 units or more)

Defective transmitting receiving

circuit of outdoor controller

circuit board

Defective transmitting receiving

circuit of indoor controller board

Defective indoor power board

2 or more outdoor units have

refrigerant address “0” .

(In case of group control)

Noise has entered into power

supply or indoor / outdoor unit

connecting wire.

(6844)

Содержание Mr.Slim PUHZ-P100VKA
















































































































Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Руководство по обслуживанию

Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды