Mitsubishi Electric Mr.Slim PUHZ-P100VKA Скачать руководство пользователя страница 46

Страница: 46 / 111

Phenomena

Factor

Countermeasure

OCH670

For 3 minutes after temperature

adjuster turns off, the compressor

will not start operating even if

temperature adjuster is turned on.

For 3 minutes after temperature

adjuster turns on, the compressor

will not stop operating even if

temperature adjuster is turned off.

(Compressor stops operating

immediately when turning off by

the remote controller.)

Normal operation

(For protection of compressor)

Normal operation

4. Even controlling by the wireless

remote controller, no beep is

heard and the unit does not start

operating. Operation display is

indicated on wireless remote

controller.

The pair number settings of the wireless remote

controller and indoor controller board are mismatched.

Check the pair number settings.

5. When operating by the wireless

remote controller, beep sound is

heard, however, unit does not start

operating.

No operation for 2 minutes at most after the power

supply ON.

Local remote controller operation is prohibited.

• Remote controlling adaptor is connected to CN32

on the indoor controller board.

• Local remote controller operation is prohibited by

centralised controller etc. since it is connected to

MELANS.

Phenomena of No.2.

Normal operation

Check the phenomena No.2.

6. Remote controller display works

normally and the unit performs

cooling operation, however, the

capacity cannot be fully obtained.

(The air does not cool well.)

Refrigerant shortage

Filter clogging

Heat exchanger clogging

Air duct short cycle

•

If refrigerant leaks, discharging

temperature rises and LEV opening

increases. Inspect leakage by checking

the temperature and opening.

•

Check pipe connections for gas leakage.

Open intake grille and check the filter.

Clean the filter by removing dirt or dust on

it.

•

If the filter is clogged, indoor pipe

temperature rises and discharging

pressure increases. Check if heat

exchanger is clogged by inspecting

discharging pressure.

•

Clean the heat exchanger.

Remove the blockage.

Содержание Mr.Slim PUHZ-P100VKA
















































































































Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Руководство по обслуживанию

Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды