Mitsubishi Electric Mr.Slim PUHZ-P100VKA Скачать руководство пользователя страница 35

Страница: 35 / 111

OCH670

Check code

Abnormal points and detection method

Judgment and action

(1302)

High pressure (High pressure switch

63H operated)

Abnormal if high pressure switch 63H

(4.15MPa) operated during compressor

operation.

Short cycle of indoor unit

Clogged filter of indoor unit

Decreased airflow caused by

dirt of indoor fan

Dirt of indoor heat exchanger

Locked indoor fan motor

Malfunction of indoor fan motor

Defective operation of stop

valve (Not full open)

Clogged or broken pipe

Locked outdoor fan motor

Malfunction of outdoor fan motor

Short cycle of outdoor unit

Dirt of outdoor heat exchanger

Decreased airflow caused by

defective inspection of outside

temperature thermistor

(It detects lower temperature

than actual temperature.)

Disconnection or contact failure

of connector (63H) on outdoor

controller board

Disconnection or contact failure

of 63H connection

Defective outdoor controller board

Defective action of linear

expansion valve

Malfunction of fan driving circuit

–

Check indoor unit and repair defect.

Check if stop valve is fully open.

Check piping and repair defect.

–

Check outdoor unit and repair defect.

Check the detected temperature of outside

temperature thermistor on LED display.

(SW2 on A-Control Service Tool : Refer

to "9-10. FUNCTION OF SWITCHES,

CONNECTORS AND JUMPERS".)

–

Turn the power off and check F5 is

displayed when the power is turned again.

When F5 is displayed, refer to “Judgment

and action” for F5.

Check linear expansion valve.

Refer to "9-6. HOW TO CHECK THE PARTS".

Replace outdoor controller board.

Case

(TH4: 1102)

(TH33: 1132)

High discharging temperature

High comp. surface temperature

1. Abnormal if discharge thermistor (TH4)

exceeds 115°C

or 110°C continuously for

5 minutes.

Abnormal if condenser/evaporator

temperature thermistor (TH5) exceeds 40°C

during defrosting and discharge thermistor

(TH4) exceeds 110°C.

2. Abnormal if discharge superheat

(TH4 - TH5) increases.

All the conditions are detected simul-

taneously for 10 minutes continuously

after 6 minutes past from compressor

startup (including the thermostat indica-

tion or recovery from defrosting).

• During compressor operation (in

Cooling only)

• When discharge superheat is less than

80°C in Cooling.

• When condensing temp of TH6 is

more than -40°C. (In Cooling only.)

3. Abnormal if comp. surface temperature

thermistor (TH33) exceeds 115°C or

110°C continuously for 5 minutes.

Overheated compressor

operation caused by shortage

of refrigerant

Defective operation of stop

valve

Defective thermistor

Defective outdoor controller

board

Defective action of linear

expansion valve

Check intake superheat.

Check leakage of refrigerant.

Charge additional refrigerant.

Check if stop valve is fully open.

Turn the power off and check if U3 is

displayed when the power is on again.

When U3 is displayed, refer to

“Judgement and action” for U3.

Check linear expansion valve.

Refer to "9-6. HOW TO CHECK THE PARTS".

<Abnormalities detected while unit is operating>

(TH4: 5104)

(TH33: 5132)

Open/short circuit of discharge

thermistor (TH4) / comp. surface

thermistor (TH33)

Abnormal if open (TH4: −20°C or less,

TH33: −20°C or less) or short (217

°C

or more) is detected during compressor

operation.

(Detection is inoperative for 10 minutes of

compressor starting process.)

Disconnection or contact failure

of connector (TH4/TH33) on

the outdoor controller circuit

board

Defective thermistor

Defective outdoor controller

circuit board

Check connection of connector (TH4/TH33)

on the outdoor controller circuit board.

Check breaking of the lead wire for

thermistor (TH4/TH33). Refer to "9-9. TEST

POINT DIAGRAM".

Check resistance value of thermistor (TH4/

TH33) or temperature by microprocessor.

(Thermistor/TH4/TH33: Refer to"9-6. HOW

TO CHECK THE PARTS".)

(SW2 on A-Control Service Tool: Refer

to "9-10. FUNCTION OF SWITCHES,

CONNECTORS AND JUMPERS".)

Replace outdoor controller board.

Содержание Mr.Slim PUHZ-P100VKA
















































































































Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Руководство по обслуживанию

Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды