Mitsubishi Electric Mr.Slim PUHZ-P100VKA Скачать руководство пользователя страница 100

Страница: 100 / 111

100

OCH670

12-1. SMOOTH MAINTENANCE

12-1-1. PAR-30MAA/PAR-31MAA

Maintenance data, such as the indoor/outdoor unit’s heat exchanger temperature and compressor operation current can be

displayed with “Smooth maintenance”.

This cannot be executed during test operation.

Depending on the combination with the outdoor unit, this may not be supported by some models.

Check menu

Cursor

Service menu:

Error history

Refrigerant volume check

Refrigerant leak check

Smooth maintenance

Request code

Smooth maintenance

Begin:

Smooth maintenance

Exit:

Ref.address

Stable mode

Cursor

−

Address

＋

Ref.address

Stable mode

Stabilization→Collecting

Cool

/ Heat/ Normal

Cool

/ Heat/ Normal

Smooth maintenance

Return:

Smooth maintenance

Return:

Smooth maintenance

Return:

Page

COMP. current

COMP. run time

COMP. On / Off

COMP. frequency

times

Ref. address

Cool

Ref.address

Cool

Ref.address

Cool

Sub cool

OU TH4 temp.

OU TH6 temp.

OU TH7 temp.

IU air temp.

IU HEX temp.

IU filter time

Select "Smooth maintenance" with the F1 or F2 button, and press the

button.

Select "Check" with the F1 or F2 button, and press the

button.

Select "Service" from the Main menu, and press the

button.

Set each item.

Select the item to be changed with the F1 or F2 button.

Select the required setting with the F3 or F4 button.

■

<Ref.address>setting [ 0 ]~[ 15 ]

■

<Stable mode>setting [ Cool ] / [Heat] / [ Normal ]

Press the

button, Fixed operation will start.

Note: Stable mode will take approx. 20 minutes.

The operation data will appear.

The Compressor-Accumulated operating (COMP. run) time is 10-hour unit, and

the Compressor-Number of operation times (COMP. On / Off) is a 100-time

unit (fractions discarded).

Navigating through the screens

• To go back to the Main menu ..........

button

• To return to the previous screen .......

button

EASY MAINTENANCE FUNCTION

Содержание Mr.Slim PUHZ-P100VKA
















































































































Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды

Mitsubishi Electric Mr.Slim PUHZ-P100VKA, Руководство по обслуживанию

Результаты поиска

Содержание Mr.Slim PUHZ-P100VKA

Отзывы:

Похожие инструкции для Mr.Slim PUHZ-P100VKA

Бренды по названию

Популярные бренды