manualshive.com logo in svg

minicopter Diabolo S, Руководство пользователя

Поделиться
Скачать
minicopter Diabolo S Скачать руководство пользователя страница 23

Attach the pinion on the mo-
tor shaft. The delivered pinion 
is normally 20T with 6mm 
shaft. There are also pinions 
with 8mm hole available, also 
pinions from 15-22T with 6mm 
shaft and from 18-22T with 
8mm shaft. If the motor shaft 
has no fl at spot then add one 
at the end of the shaft (mark 
the position before, pinion 
should be 0.5-1mm away from 
the lower motor carrier plane).

Tighten now the grub screws 
M4x5 D35, beginning with the 
one on the fl at spot. 

Now install the motor using 
four hex screws M3x8 and 
washers 3mm 002 using Locti-
te. The plastic gear wheel is a 
high temperature high tech po-
lymer that is uncritical against 
any heat. You should feel a 
small but noticable play bet-
ween pinion and gear wheel. 
For 21 or 22T pinions you must 
fi le the long holes 0.5 or 1mm 
to the front using a needle fi le. 
During mount press the motor 
down that it is really vertical.

Содержание Diabolo S





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды