MillRight CARVE KING 2 Скачать руководство пользователя | Manualshive

Страница: 13 / 34

background image

Page 13 or 34

Z Motor Mount

Parts

Z Motor Mount

X/Z Motor Spacer Plate

Long Wire Motor

X Drag Chain Post

Hardware

(4) M3x16

(1) M4x12

(1) M4 Split-Lock Washer

Tools

Phillips Screwdriver

Put the motor on the table with the cord pointing
away from you.  Place the Motor Spacer Plate on the
motor.  Place the Z Motor Mount on the Motor
Spacer Plate.  Screw in (4) M3x16 machine screws into
the motor.

Make sure the motor is centered with the Motor
Spacer Plate and the Z Motor Mount. Tighten screws.

Lay the motor on its side. Attach the X Drag Chain
Post using a M4x12 Machine Screw with an M4 Split-
Lock Washer. Tighten. Place to the side. Note that
the X Drag Chain Post is just a cylinder with holes
tapped on each side. Do not confuse this with the Y
Drag Chain Post, which has additional features
machined into it.

«
...
11
12
13
14
15
...
»

Содержание CARVE KING 2



































Отзывы:

Нет отзывов

Похожие инструкции для CARVE KING 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: Garaventa Lift Страницы: 58

Бренд: Hama Страницы: 7

Бренд: Hama Страницы: 44

Бренд: RadioMaster Страницы: 10

Бренд: K&K Страницы: 6

Бренд: Walimex Pro Страницы: 68

Бренд: S&P Страницы: 17

Бренд: S&S Northern Страницы: 9

Бренд: Taco Electronic Solutions Страницы: 28

Бренд: Samson Страницы: 6

Бренд: Xilinx Страницы: 2

sensoCOMFORT VRC 720/3

Бренд: Vaillant Страницы: 64

Бренд: Parker Страницы: 8

Бренд: Global Fire Equipment Страницы: 23

Бренд: KSB Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды