MillRight CARVE KING 2 Скачать руководство пользователя | Manualshive

Страница: 34 / 34

background image

Page 34 or 34

Installing the Router

Parts

Makita Router

Hardware

None (all items already installed)

Tools

Phillips head screw-driver or 3mm Hex Key
(depending on hardware type in mount)

Place the router into the mount and tighten the pinch
bolt to collapse the router mount around the router
body. The position of the router in the mount does
not have to be exact. As depth in the mount like
pictured to the right is a good starting point. This
allows the router to reach the bed with most cutters
while still allowing for good bed clearance when at
maximum height.

Congratulations! Assembly is complete. Check out the

www.millrightcnc.com/resources

for more

information on connecting to the machine and running your

first program.

Be sure to join our forum at

www.millrightcnc.proboards.com

to connected with the CNC community and share your build.

«
...
32
33
34

Содержание CARVE KING 2



































Отзывы:

Нет отзывов

Похожие инструкции для CARVE KING 2

Бренд: Samson Страницы: 78

Бренд: Rachio Страницы: 16

Бренд: Fagor Страницы: 10

Бренд: Fagor Страницы: 358

Бренд: Fagor Страницы: 556

Бренд: Fagor Страницы: 172

Бренд: Fagor Страницы: 180

Бренд: Fagor Страницы: 112

Master Control Unit

Бренд: FaderMate Страницы: 36

Бренд: Ravaglioli Страницы: 90

Бренд: Raypak Страницы: 24

Бренд: rauland Страницы: 2

Бренд: J+J Страницы: 91

Бренд: Data Signs Страницы: 23

Бренд: East Coast Datacom Страницы: 14

Total Access 351 Series

Бренд: ADTRAN Страницы: 4

Бренд: Sabiana Страницы: 60

Бренд: Barco Страницы: 158

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды