Miller Bobcat 250 NT Скачать руководство пользователя

Страница: 40 / 80

OM-4403 Page 36

8-5.

Adjusting Engine Speed (Kohler-Powered Units)

Ref. 801 188-D / 801 209-A

After tuning engine, check engine
speeds with a tachometer (see
table). If necessary, adjust speeds
as follows:

Start engine and run until warm.
Turn Fine Control to 10.

Remove top cover to access speed
adjustments.

Idle Speed Adjustment

Move Engine Control switch to
Run/Idle position.

Throttle Solenoid

Mounting Screws

Idle Speed Screw

Loosen mounting screws. Adjust
solenoid position so engine runs at
idle speed. If necessary, back out
idle speed screw so solenoid can
be moved to correct position. Tight-
en mounting screws. Be sure sole-
noid linkage works smoothly.

Turn idle speed screw for fine ad-
justments.

Weld/Power Speed Adjustment

Move Engine Control switch to Run
position.

Weld/Power Speed
Adjustment Nut

Lock Nut

Loosen lock nut. Turn adjustment
nut until engine runs at weld/power
speed. Tighten lock nut.

Reinstall top cover.

Stop engine.

1/4, 3/8 in

Top View

Tools Needed:

2200

50 rpm

3700

50 rpm

Содержание Bobcat 250 NT

















































































Результаты поиска

Содержание Bobcat 250 NT

Отзывы:

Похожие инструкции для Bobcat 250 NT

Бренды по названию

Популярные бренды

Miller Bobcat 250 NT, Руководство пользователя

Результаты поиска

Содержание Bobcat 250 NT

Отзывы:

Похожие инструкции для Bobcat 250 NT

Бренды по названию

Популярные бренды