Miller Bobcat 250 NT Скачать руководство пользователя

Страница: 35 / 80

OM-4403 Page 31

7-6.

Adjusting Engine Speed (Onan-Powered Units)

800 392-J / 802 457

After tuning engine, check engine
speeds with a tachometer (see
table). If necessary, adjust speeds
as follows:

Start engine and run until warm.

Remove wrapper to access speed
adjustments.

Idle Speed Adjustment

Move Engine Control switch to
Run/Idle position.

Throttle Solenoid

Mounting Screws

Idle Speed Screw

Loosen mounting screws. Adjust
solenoid position so engine runs at
idle speed. If necessary, back out
idle speed screw so solenoid can
be moved to correct position. Tight-
en mounting screws. Be sure sole-
noid linkage works smoothly.

Turn idle speed screw for fine
adjustments.

Weld/Power Speed Adjustment

Move Engine Control switch to Run
position.

Jam Nut

Lock Nut

Weld/Power Speed
Adjustment Screw

Loosen jam nut and lock nut. Turn
adjustment screw until engine runs
at weld/power speed. Tighten jam
nut, and then tighten lock nut.

Stop engine.

Reinstall wrapper.

2200

100 rpm

3700

50 rpm

8 mm

Tools Needed:

10 mm

Содержание Bobcat 250 NT

















































































Результаты поиска

Содержание Bobcat 250 NT

Отзывы:

Похожие инструкции для Bobcat 250 NT

Бренды по названию

Популярные бренды

Miller Bobcat 250 NT, Руководство пользователя

Результаты поиска

Содержание Bobcat 250 NT

Отзывы:

Похожие инструкции для Bobcat 250 NT

Бренды по названию

Популярные бренды