Miller Bobcat 250 NT Скачать руководство пользователя

Страница: 28 / 80

OM-4403 Page 24

SECTION 6 – OPERATING AUXILIARY EQUIPMENT

6-1.

Standard Receptacles

Ref. 200 017

If unit does not have GFCI re-
ceptacles, use GFCI-protected
extension cord.

Generator power decreases as
weld current increases.

Set Fine Control R1 at 10 for full
generator power.

240 V 50 A AC Receptacle RC1

RC1 supplies 60 Hz single-phase
power at weld/power speed. Maxi-
mum output is 10 kVA/kW.

120 V 20 A AC Duplex Recep-
tacle RC2

120 V 20 A AC Duplex Recep-
tacle RC3

RC2 and RC3 supply 60 Hz single-
phase power at weld/power speed.
Maximum output from RC2 or RC3 is
2.4 kVA/kW.

Circuit Breakers CB1 and CB2

CB1 and CB2 protect RC1 from over-
load. If CB1 or CB2 opens, RC1 and
one of the 120 volt receptacles does
not work. 120 volts may still be pres-
ent at RC1.

Power is still present at the 240
volt receptacle when only one
circuit breaker trips.

Unplug power cord before at-
tempting to service accesso-
ries or tools.

Circuit Breaker CB3

Circuit Breaker CB4

CB3 protects RC2 and CB4 protects
RC3 from overload. If a circuit break-
er opens, the receptacle does not
work.

Press button to reset circuit
breaker. If breaker continues to
open, contact Factory
Authorized Service Agent.

Combined output of all receptacles
limited to 10 kVA/kW rating of the gen-
erator.

EXAMPLE: If 20 A is drawn from
each 120 V duplex receptacle, only
21 A is available at the 240V
receptacle:

2 x (120 V x 20 A) + (240 V x 21 A) =
10 kVA/kW

Содержание Bobcat 250 NT

















































































Результаты поиска

Содержание Bobcat 250 NT

Отзывы:

Похожие инструкции для Bobcat 250 NT

Бренды по названию

Популярные бренды

Miller Bobcat 250 NT, Руководство пользователя

Результаты поиска

Содержание Bobcat 250 NT

Отзывы:

Похожие инструкции для Bobcat 250 NT

Бренды по названию

Популярные бренды