Miller Bobcat 250 NT страница 36 Скачать руководство пользователя

Страница: 36 / 80

OM-4403 Page 32

7-7.

Servicing Optional Spark Arrestor (Onan-Powered Units)

Ref. 801 682-A / Ref. 183 175–A

Stop engine and let cool.

Spark Arrestor Screen

Clean and inspect screen. Replace
spark arrestor if screen wires are
broken or missing.

1/4 in

Tools Needed:

SECTION 8 – MAINTENANCE – (KOHLER-POWERED UNITS)

8-1.

Routine Maintenance (Kohler-Powered Units)

Follow the storage procedure in the engine owner’s manual if the unit will not be used for an
extended period.

Note

Recycle

engine

fluids.

Stop engine before maintaining.

See also Engine Manual and maintenance label. Ser-
vice engine more often if used in severe conditions.

To be done by Factory Authorized Service Agent.

8 h

Wipe up spills.

Check fluid levels.
See Section 4-3.

20 h

25 h

Check and clean optional
spark arrestor screen. See
Section 8-7.

Service air cleaner
wrapper (foam element).
See Section 8-3.

50 h

Clean and tighten weld
terminals.

Содержание Bobcat 250 NT

















































































Результаты поиска

Содержание Bobcat 250 NT

Отзывы:

Похожие инструкции для Bobcat 250 NT

Бренды по названию

Популярные бренды

Miller Bobcat 250 NT, Руководство пользователя

Результаты поиска

Содержание Bobcat 250 NT

Отзывы:

Похожие инструкции для Bobcat 250 NT

Бренды по названию

Популярные бренды