MIHM-VOGT TABEO Series Скачать руководство пользователя страница 44

Страница: 44 / 46

Page 44

Operating Manual Tabeo Sintering Oven Metal

Version 4.0en

10/2018

Faults and error messages

Error messages

Fault

Possible cause

Troubleshooting

Responsi-

bility

"Er00" displayed

Door open during process

Close door (“Press”)
Poss. readjust door locking

User
Service de-

partment

“Er01" displayed

Excessive temperature

Replace the thermocouple.

Service de-

partment

"Er02" displayed

Broken sensor, measuring

circuit

Retighten the thermocouple con-

nections.

"Er03" displayed

Broken sensor

Replace the thermocouple.

“Er04" displayed

Thermocouple reverse polar-

ity

Connect thermocouple correctly

+ orange line
- white line

"Er05" displayed

Thermocouple short-circuit-

ed or heater defective

Check the heater/thermocouple

and have it/them replaced if nec-

essary.

"Er06" displayed

Defective electronic system

Check the electronic system and

have it replaced if necessary.

"Er09" displayed

Power failure

If there is a brief power failure

during a heating-up or cool-

ing-down phase and the tempera-

ture is below 1000 °C, the process

will be continued once power has

been restored. If the power failure

lasts longer than 10 seconds and

the temperature is above 1000 °C,

the process will be stopped and

the display will flash.

The

Start/

Stop

but-

ton must be

pressed to

acknowledge

error Er09.

Содержание TABEO Series















































Результаты поиска

Содержание TABEO Series

Отзывы:

Бренды по названию

Популярные бренды

MIHM-VOGT TABEO Series, Оригинальное руководство по эксплуатации

Результаты поиска

Содержание TABEO Series

Отзывы:

Бренды по названию

Популярные бренды