Mighty Mule Automatic Gate Opener System Скачать руководство пользователя | Manualshive

Страница: 20 / 44

background image

16

Mounting the Opener

Step 11

Attach the opener to the securely bolted post bracket assembly and gate bracket using clevis pins, washers, and hairpin clips,
or optional Pin Locks (see Accessory Catalog). Verify that the opener is level and adjust the post bracket assembly if
necessary.

Mounting the Second Opener

Step 12

Mount the second opener on the remaining gate leaf by repeating Step 3 through Step 11, starting on page 13.
After you have mounted the second opener, proceed to Step 13 on the next page.

Level Opener

Fence Post

Gate In Open Position

LEVEL horizontal cross member

Post Bracket Assembly
bolted to fence post

Clevis Pin, Washer, and Hairpin Clip

Clevis Pin, Washer, and Hairpin Clip

Gate Bracket bolted
to gate cross member

®

E-Z GATE OPEN

ER

«
...
18
19
20
21
22
...
»

Содержание Automatic Gate Opener System













































Отзывы:

Нет отзывов

Похожие инструкции для Automatic Gate Opener System

Бренд: SOMFY Страницы: 4

Бренд: Chamberlain Страницы: 2

Бренд: Chamberlain Страницы: 36

Бренд: SkyLink Страницы: 2

Бренд: Filo Страницы: 29

Бренд: digigate slider Страницы: 7

Бренд: CAME Страницы: 28

Бренд: Automatic Technology Страницы: 48

Бренд: V2 Страницы: 100

Estate Swing E-SC 1102 Series

Бренд: FAAC Страницы: 38

Бренд: Hamilton Beach Страницы: 16

Бренд: jcm-tech Страницы: 8

Бренд: CAME Страницы: 2

SeceuroGlide LT

Бренд: SWS Страницы: 11

Бренд: CAME Страницы: 2

Бренд: Enjoy-Motors Страницы: 20

Бренд: Calimet Страницы: 42

Бренд: Weibel Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды