Mighty Mule Automatic Gate Opener System Скачать руководство пользователя | Manualshive

Страница: 5 / 44

background image

1

IMPORTANT SAFETY INSTRUCTIONS

Because automatic gate openers produce high levels of force, consumers need to know the potential hazards associated with
improperly designed, installed, and maintained gate opener systems.

Keep in mind that the gate opener is just one

component of the total gate operating system

. Each component must work in unison to provide the consumer with

convenience, security, and safety.

This manual contains various safety precautions and warnings for the consumer. Because there are many possible
applications of the gate opener, the safety precautions and warnings contained in this manual cannot be completely
exhaustive in nature. They do, however, provide an overview of the safe design, installation, and use of this product.
CAREFULLY READ AND FOLLOW ALL SAFETY PRECAUTIONS, WARNINGS, AND INSTALLATION
INSTRUCTIONS TO ENSURE THE SAFE SYSTEM DESIGN, INSTALLATION, AND USE OF THIS PRODUCT.

Precautions and warnings in this manual are identified with this warning symbol. The symbol identifies conditions that
can result in damage to the opener or its components, serious injury, or death.

Because GTO automatic gate openers are

only

part

of the total gate operating system, it is the responsibility of the

consumer to ensure that the total system is safe for its intended use.

Clevis Pin

Hairpin Clip

Washer

Gate Bracket

Front Mount

Disconnecting the Openers

1.

Turn control box power switch OFF.

2.

Remove hairpin clip, clevis pin, and washer from
front mount.

3.

Pull front mount away from gate bracket.

Repeat steps 1 – 3 for the second opener

Your dual gate can be opened and closed manually
when the openers are disconnected.

NOTE: Substitute Pin Locks for the clevis

pins to prevent unauthorized removal of the
openers from the gate (see Accessory
catalog).

To Manually Open and Close
the Gate, Follow the Procedure
Below:

CAUTION: Disconnect the
openers ONLY when the control
box power switch is OFF and
the gate is NOT moving.

«
...
3
4
5
6
7
...
»

Содержание Automatic Gate Opener System













































Отзывы:

Нет отзывов

Похожие инструкции для Automatic Gate Opener System

Бренд: Gartentorschliesser.com Страницы: 20

8550WRGD Admiral II

Бренд: Raynor Страницы: 44

Бренд: FAAC Страницы: 8

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 34

Бренд: Craftsman Страницы: 24

Бренд: Craftsman Страницы: 84

Бренд: Craftsman Страницы: 100

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 100

ZEROQUATTRO 180

Бренд: O&O Страницы: 2

Бренд: V2 Страницы: 148

Бренд: Genie Страницы: 32

GDO BATTERY KIT

Бренд: SOMFY Страницы: 16

Бренд: CAME Страницы: 2

Бренд: CAME Страницы: 20

Бренд: CAME Страницы: 24

Бренд: tau Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды