Mighty Mule Automatic Gate Opener System Скачать руководство пользователя | Manualshive

Страница: 27 / 44

background image

23

NOTE: This setting will work if you are using CLOSED POSITION STOP PLATES

but WILL NOT work if you are using a LOCK

BOTH OPERATORS OPEN SIMULTANEOUSLY
SECOND OPERATOR CLOSES FIRST

SEQ1 = OFF SEQ2 = OFF (factory setting)

If both SEQ1 and SEQ2 are set to OFF, the FIRST OPERATOR and SECOND
OPERATOR open simultaneously. The SECOND OPERATOR will close first.

NOTE: This is the setting you need to use with

CLOSED POSITION STOP PLATES and/or LOCK

FIRST OPERATOR OPENS FIRST,
SECOND OPERATOR CLOSES FIRST

SEQ1 = OFF SEQ2 = ON

If SEQ1 is set to OFF, and SEQ2 is set to ON, the FIRST OPERATOR will open
first, and the SECOND OPERATOR will close first.

NOTE: This setting can not be used if you are using

CLOSED POSITION STOP PLATES or a LOCK

FIRST OPERATOR OPENS FIRST,
FIRST OPERATOR CLOSES FIRST

SEQ1 = ON SEQ2 = ON

If SEQ1 is set to ON, and SEQ2 is set to ON, The FIRST OPERATOR opens and
closes first.

NOTE: This setting can not be used if you are using

CLOSED POSITION STOP PLATES or a LOCK

BOTH OPERATORS OPEN SIMULTANEOUSLY
BOTH OPERATORS CLOSES SIMULTANEOUSLY

SEQ1 = ON SEQ2 = OFF

If SEQ1 is set to ON, and SEQ2 is set to OFF, the FIRST OPERATOR and
SECOND OPERATOR open and close simultaneously.

Replace the control box cover and fasten it with (4) screws. Turn the
control box power switch ON. The system will energize in approximately
15 seconds.

1234

ON

OBSTRUCT
SENS.

PULL/PUSH

SEQ1

SNGL/DUAL

SEQ2

MIN

MAX

LEARN

1234

ON

OBSTRUCT
SENS.

PULL/PUSH

SEQ1

SNGL/DUAL

SEQ2

MIN

MAX

LEARN

1234

ON

OBSTRUCT
SENS.

PULL/PUSH

SEQ1

SNGL/DUAL

SEQ2

MIN

MAX

LEARN

1234

ON

OBSTRUCT
SENS.

PULL/PUSH

SEQ1

SNGL/DUAL

SEQ2

MIN

MAX

LEARN

DIP Switch Settings for Gate Sequencing

«
...
25
26
27
28
29
...
»

Содержание Automatic Gate Opener System













































Отзывы:

Нет отзывов

Похожие инструкции для Automatic Gate Opener System

Бренд: Wayne-Dalton Страницы: 20

Бренд: Wayne-Dalton Страницы: 4

Бренд: Wayne-Dalton Страницы: 22

Бренд: Aprimatic Страницы: 3

Бренд: CAME Страницы: 2

Бренд: GATEXPERT Страницы: 26

Бренд: Novoferm Страницы: 32

Бренд: FAAC Страницы: 14

Бренд: TdA Страницы: 9

Бренд: Grifco Страницы: 24

Бренд: Xtreme Garage Страницы: 28

Бренд: Hy-Security Страницы: 78

Бренд: Chamberlain Страницы: 40

AccessMaster Security+ M150

Бренд: Chamberlain Страницы: 36

Бренд: Roger Technology Страницы: 16

IntelliSlide X6

Бренд: IQ Gate Systems Страницы: 30

IntelliSwing IQ-500-S

Бренд: IQ Gate Systems Страницы: 29

FIBO 300 LB-1,5 HP

Бренд: fadini Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды