Mighty Mule Automatic Gate Opener System Скачать руководство пользователя | Manualshive

Страница: 25 / 44

background image

21

Mounting the Receiver

Consider the following when mounting the receiver:

• Standard receiver cable length is 10 feet (receivers with a longer cable are available as

special order items; call the GTO Sales Department). NEVER splice receiver cable!

• Run the cable through PVC conduit to protect it from damage.
• DO NOT run cable through metal conduit because the receiver signal range will be

decreased.

• DO NOT run cable in conduit containing AC wiring.
• DO NOT mount receiver on a metal fence or post; doing so will decrease signal range.
• DO NOT overtighten the mounting screws; the receiver housing could be warped and

the weather seal damaged.

• The receiver range can vary from 50 to 100 feet depending upon weather, topography,

and external interference.

FCC Regulation
This device complies with FCC rules Part 15. Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept an interference that may cause undesired operation.

Transmitter distance may vary due to circumstances beyond our control. NOTE: The manufacturer is not
responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
Such modifications could void the user’s authority to operate the equipment.

Step 25

DO NOT connect the power cables during this step. Before you connect the power cables to the openers, the control board
must be set to accommodate your dual gate application. Read the DIP Switch Settings section on page 22.

SECOND OPERATOR

FIRST OPERATOR

POWER IN

ALARM

18VAC SOLAR

~ ~ –

+

RED

BLK

ORG

BLU

GRN

CLS EDG

OPN EDG

RED

BLK

ORG

BLU

GRN

CLS EDG

OPN EDG

Power Cable

from First Opener

Power Cable

from Second Opener

RED

BLACK

ORANGE

BL

UE

GREEN

Step 24

Strip approximately 3/16" of insulation from each wire of the
40 foot power cable. Twist each exposed wire tightly. Insert
the second opener power cable upward through the right
strain relief (if necessary, loosen the sealing nut). Thread
approximately 4" of wire into the control box. Retighten
strain relief (on the

black sheath

of the power cable) until the

power cable locks into place.

Insert the stripped wires of the power cable into the
appropriate terminals on the SECOND OPERATOR
terminal block. The green wire should be inserted into the
GRN terminal, the blue wire into BLU, the orange wire into
ORG, black wire into BLK, and the red wire into the RED
terminal.

Tighten the set screws against the end of the wires.

«
...
23
24
25
26
27
...
»

Содержание Automatic Gate Opener System













































Отзывы:

Нет отзывов

Похожие инструкции для Automatic Gate Opener System

BOTTICELLI B CRC 480 D01

Бренд: BFT Страницы: 40

Бренд: Chamberlain Страницы: 80

TOP EVO TOP 291E

Бренд: GBD Страницы: 24

Бренд: GMI Страницы: 2

Бренд: CAME Страницы: 12

GOLD400D Series

Бренд: V2 Страницы: 172

Бренд: CAME Страницы: 28

Бренд: Beninca Страницы: 24

COMMANDER 2000RGD

Бренд: Raynor Страницы: 72

Бренд: CAME Страницы: 112

Бренд: Accessmatic Страницы: 60

Бренд: Black & Decker Страницы: 2

Бренд: Gatekeeper Страницы: 22

Бренд: Nice Apollo Страницы: 26

Бренд: Tymetal Corp. Страницы: 36

Бренд: Ricon Страницы: 4

Бренд: Cookworks Страницы: 8

Бренд: Cookson Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды