Mighty Mule Automatic Gate Opener System Скачать руководство пользователя | Manualshive

Страница: 41 / 44

background image

37

Column Installation Information

I

F THESE OPENERS WILL BE USED WITH GATES THAT ARE MOUNTED ON

MASONRY, BRICK, OR ROCK (etc.) COLUMNS:

READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING

Attaching a gate opener to a gate mounted on a masonry column requires special procedures.

Here's how to check your installation to minimize problems:

Open the gate to the 90º position, then measure the distance between the back of the gate and the face of
the column. If there is at least a 6 1/4" clearance, you may not have to make any special modifications.
However, you must measure the post pivot bracket position using 4 1/2" x 4 1/2" setback, as described on
page 14 of this manual, to verify that the gate hinge sits far enough from the column to give your
installation the proper setback distance.

If you do not have the proper clearance or setback distance, the opener may operate the gate for a while, but eventually
the unit will become nonfunctional. To prevent this problem, we suggest the following installation method:

A.

The simplest solution is to install the opener in a push-to-open configuration (requires Push-To-Open Brackets,
see Accessory Catalog). The crucial 4 1/2" setback is easier to achieve and clearance is no longer a problem,
since the opener will be pushing the gate away from the column instead of pulling it toward the column. It is
recommended that you place a steel plate between the opener mounting brackets and masonry surface for
additional strength.

B.

If a push-to-open installation is impossible due to traffic hazards, terrain, etc., another option is to re-hang the
gate. You may hang it on a post, either in the center of the column or at the back corner, or move the gate to the
back corner of the columns.

C.

The most difficult solution is to cut a notch in the column to accommodate the opener and power cable. This
job is NOT for the inexperienced!

Because of the difficulty associated with column installations, we STRONGLY advise you to call the GTO
Service Department at (800) 543-1236 or (850) 575-4144 for assistance

prior

to your installation.

«
...
39
40
41
42
43
...
»

Содержание Automatic Gate Opener System













































Отзывы:

Нет отзывов

Похожие инструкции для Automatic Gate Opener System

Бренд: Elsema Страницы: 12

Бренд: GATEXPERT Страницы: 33

Бренд: Hamilton Beach Страницы: 8

Security+ 3130M

Бренд: Chamberlain Страницы: 36

Бренд: SOMFY Страницы: 12

Бренд: Dea Страницы: 44

Бренд: Dea Страницы: 48

Бренд: Beninca Страницы: 14

Commander II Safety Signal 3240RGD

Бренд: Raynor Страницы: 36

Бренд: Wayne-Dalton Страницы: 25

Бренд: CAME Страницы: 2

GDO-2 SecuraLift

Бренд: Automatic Technology Страницы: 24

GDO-11v1 SecuraLift

Бренд: Automatic Technology Страницы: 36

Бренд: Automatic Technology Страницы: 36

Бренд: Automatic Technology Страницы: 19

Бренд: Automatic Solutions Страницы: 16

SecuraLift Rhino

Бренд: Automatic Technology Страницы: 36

Бренд: Automatic Solutions Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды