Miele T 8626 WP Скачать руководство пользователя страница 39

Страница: 39 / 60

Problem

Possible cause

Remedy

There are humming
noises.

The compressor is
operating.

These noises are quite
normal and do not indicate a
fault.

The display is dark.
The programme
selector is not lit up.
The Start/Stop button
light flashes slowly.

The display has
switched off
automatically to save
energy (Standby mode).

The programme selector
lighting goes out when

Settings

is selected.

The display will light up
when one of the buttons is
pressed.

The Start/Stop button
light flashes/does not
flash.

The flashing indicates
that a programme can
be started.

After the programme has
started, the flashing will
change to a constant light.

The programme does
not start.

No obvious cause.

– Is the dryer switched on?

– Is the plug correctly

inserted into the socket
and switched on?

– Is the door closed

properly?

– Has the fuse or circuit

breaker tripped?

The display is in a
different language.

A different language has
been selected.

Set the language you want.
The

flag symbol

will guide

you.

Power cut.

A programme which was running previously will
continue automatically when power is restored to the
tumble dryer as long as the Cooling down phase had
not been reached.

The interior drum
lighting does not
come on.

The lighting switches off
automatically (to save
energy).

– Switch the dryer off and

then on again.

– If the lamp needs to be

replaced, follow the
instructions in "Changing
the lamp" at the end of this
section.

Problem solving guide

Содержание T 8626 WP





























































Результаты поиска

Содержание T 8626 WP

Отзывы:

Похожие инструкции для T 8626 WP

Бренды по названию

Популярные бренды

Miele T 8626 WP, Руководство по эксплуатации

Результаты поиска

Содержание T 8626 WP

Отзывы:

Похожие инструкции для T 8626 WP

Бренды по названию

Популярные бренды