Miele T 8626 WP Скачать руководство пользователя страница 53

Страница: 53 / 60

To open the Settings menu

Close the door.

Switch the dryer on.

Press both menu buttons at the same
time until the following appears in the
display:

Settings

Language

Continue

You are now in the

Settings

menu.

Select the setting you want with the left
hand

Menu

button under

Continue

and confirm your selection with the right
hand

Menu

button under

To close the Settings menu

Settings

Back

Continue

Press the right hand

Menu

button

under

Language

The display can be set to appear in
one of several different languages.

Select the language you want by
pressing the left hand

Menu

button

under

(Continue).

A tick

will appear beside the

language to show that it has been set.

The flag

after the word

Language

acts as a guide to prevent a language
which will not be understood from
being set.

Settings menu

Содержание T 8626 WP





























































Результаты поиска

Содержание T 8626 WP

Отзывы:

Похожие инструкции для T 8626 WP

Бренды по названию

Популярные бренды

Miele T 8626 WP, Руководство по эксплуатации

Результаты поиска

Содержание T 8626 WP

Отзывы:

Похожие инструкции для T 8626 WP

Бренды по названию

Популярные бренды