background image

Cool air

Max. load 6 kg*

Fabric type

Any item which only needs airing.

Extra options

Anti-crease, Buzzer

Au

Max. load 4.5 kg*

, Normal, Hand iron

r

Fabric type

Mixed loads of garments suitable for the

Cottons

and

Minimum

iron

programmes. Sort according to colour.

Extra options

Anti-crease, Buzzer

Shirts

Max. load 2 kg*

, Normal, Hand iron

r

Fabric type

Shirts and blouses.

Extra options

Gentle tumble or Freshen up, Anti-crease, Buzzer

Denim

Max. load 3 kg*

Normal, Hand iron

r

Fabric type

Denim garments, e.g. jeans, jackets, skirts, shirts.

Extra options

Gentle tumble or Freshen up, Anti-crease, Buzzer

Woollens handcare

Max. load 2 kg*

Fabric type

Woollen fabrics. Fabrics containing wool blends.

Note

– Woollen garments are fluffed up.

– Remove garments immediately at the end of the programme.

Extra option

Buzzer

Silks handcare

Max. load 1 kg*

Fabric type

Silks (which are suitable for drying in a tumble dryer) e.g. blouses
and shirts.

Notes

– Smooths out creasing.

– Remove garments immediately at the end of the programme.

Extra options

Anti-crease, Buzzer

*

Weight of dry laundry

Programme chart

24

Содержание T 8626 WP





























































Отзывы: