Miele T 8626 WP Скачать руководство пользователя страница 14

Страница: 14 / 60

If the tumble dryer has not been

transported as described in
"Installation" then it must be left to
stand for at least 1 hour before it is
connected to the electricity supply.

When the tumble dryer is switched on
for the first time, the welcome screen
will appear.

The welcome screen will appear in the
display every time you switch the dryer
on until you have run a programme
lasting longer than 1 hour.

The display for setting the language will
then appear.

Setting the language in the display

If the language showing in the display
is the one you want, then confirm this
with

If you want to select a different
language:

Sprache

deutsch

)

Select the language you require by
pressing the left hand

Menu

button

under

Confirm your selection by pressing
the right hand

Menu

button under

It is possible to select another language
at any time via the

Settings

menu.

Setting the time (of day) *

* The time may already have been set
at the factory. If it has, and is correct,
you can skip this section.

It is possible to alter the time at any
stage via the

Settings

menu.

:00

Change

Select the hours you want by
pressing the left hand

Menu

button

under

Change

, and confirm this with

the right hand

Menu

button under

Then set and confirm the minutes.

Entry menu

The entry menu showing the current
time of day will appear after the tumble
dryer has been switched on, until you
select a programme.

10 : 00

Select programme

You can now load the laundry into the
dryer and select a programme as
described in "How to dry correctly".

Before using for the first time

Содержание T 8626 WP





























































Результаты поиска

Содержание T 8626 WP

Отзывы:

Похожие инструкции для T 8626 WP

Бренды по названию

Популярные бренды

Miele T 8626 WP, Руководство по эксплуатации

Результаты поиска

Содержание T 8626 WP

Отзывы:

Похожие инструкции для T 8626 WP

Бренды по названию

Популярные бренды